Jump to content
SAU Community

Recommended Posts

If the guy is speeding, let him pass - do everything you can to let them by - two reasons.  1. there could be an emergency (not likely, but it may happen) and if you were in a similar situation, you would appreciate people getting out of the way.  

Word.. for some reason people in Perth can't handle the fact that someone might want to go a bit faster than they are on a freeway.

I challenge any right hand lane hog to go drive in the UK or Europe for a while and see how long it takes before either a cop fines them for obstructing traffic or someone rams them off the road...

(guess who's just witnessed crappy Perth driving after a month driving round the UK:D)

/rant

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Well, yesterday I saw my skyline's life flash before my eyes as I encountered my dickhead perth driver story. Driving through suburbia, doin 50km/h, just commuting along between my parents place and my house. Passing an oval where footy is being played and as I come up to a corner, I see a white camry waiting to pull out. He's stopped so I continue at 50 up the hill. No more than 10-15m from the corner now, he applies the gas and pulls out in front of me. No time. I lock it up and start sliding on wet road. Fortunatley, instinct doesn't overrule my brain and i take my foot off the brake, furiously steer to the other side of the road to swerve around this bloke, reapply the brakes, now heading for opposite curb on wrong side of road, trying to take in where other cars are (oncoming, camry driver, my car), manage to again release my locked up brakes and steer away from curb as i complete my severe swerve around this dickhead. I come to a stop safely on my side of the road, in the original direction i was heading, check that i haven't shat/pissed myself and check rear vision mirror only to see this clown simply drive off in the opposite direction like nothing had happened. Meanwhile, I'm having heart pulputations.

Fortuantley, both myself and my car are all in one piece and without a single scratch. Time to go buy lotto ticket.

Dickheads....




  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...