Jump to content
SAU Community

Recommended Posts

Available all over the place in kits, but I discovered Fulcrum sell them separately so went out and grabbed some.

Large ones (80mm OD) for $17.56ea

Small ones (69.5mm OD) for $14.10ea

I just got the 4, but I suppose if I ever wanted to change the setup i could just go back and get another 2 small ones.

Their small ones don't come with a cut in them, so you may need to cut them if you want easier fitment for either a drift or drag setup.

Depending on how you want to set the rear cradle you only need to buy 4 pineapples. I have set mine in the standard position and only required 2 large and 2 small pineapples. If you want either a drift or drag setup you would need 4 small pineapples.

Total cost was under $65.

Fitting is simple and takes approx 45 - 60mins.

Tools required:

-17mm socket and breaker bar

-14mm socket

-trolley jack

-ramps make life easier

Photos below, as well as a link to the whiteline fitting instructions. They are pretty self explanatory, so once you have a read, look at the photos, and then have a look under your car it should be obvious what needs to go where etc.

I just backed my car up onto some car ramps (remembering to chock the front wheels), then did one side at a time, while supporting the subframe with a trolley jack (it didn't really seem to need supporting but that is what is stated in the instructions).

The Whiteline instructions only mention removing 2 nuts either side (one at the front and one at the back), but I removed an additional 2 at the front from the subframe mounting bracket (marked in the photos) to make getting the front pineapples on easier.

On the front I had to use the jack once I had fitted the pineapple to compress the subframe up enough to get the nut back on with a decent amount of thread, but once it was on it tightens easily.

The rear nuts are a bit hard to get at with a socket/ratchet due to the HICAS tie-rods sitting directly under the nut, so depending on the length/chunkiness of the socket and ratchet/breaker bar you are using, you may need a 17mm spanner as well.

Torque wise, I just tightened everything until I couldn't tighten it anymore (within reason). The nuts were pretty hard to break at first when removing them so I'd say you are pretty right to tighten like a bastard.

If anyone can see anything I have done wrong or would care to elaborate on anything, feel free :)

:(

Whiteline fitting instructions:

http://www.whiteline.com.au/docs/instructs...203a_KCA349.pdf

Front mounting position. Just underneath in front of the rear wheels:

pineapples-front.jpg

Rear:

pineapples-rear.jpg

Link to comment
https://www.sau.com.au/forums/topic/61229-r33-suspension-fitting-pineapples/
Share on other sites

I think there is an all-round improvement in the rear end. Acceleration feels like it has improved and possibly braking also. There is less squatting and pitching when getting on and off the brake and accelerator.

When cornering there seems to be less rear end movement side to side as well, so overall I reckon for the price, they have made a marked difference/improvement.

Yes, the factory bushes are liquid filled and do have a tendancy to leak. I don't know how or if the pineapples will stop the factory bushes from perishing, but they seem to be Ok at the moment...

nope, not bad,

just wont get you the best performance.

u buy them from whiteline www.whiteline.com.au

or from any fulcrum dealer, www.fulcrumsuspensions.com

thanks warwick for the help,

i manged to do mine in 30 mins today and then did jlnewtons GTR aswell,

taht was a little trickier cause i had to remove the extra sway bar that the GTR has.

I got mine from the nissansilvia forums for $60 or so.

The guy there was selling them as a trader so he had heeps.

They're going in this week (read my story here)

I'm going to ask them to be put in on the neutral setting. I figure my car slides happily at the moment so going any more to drift setting would be suicide (or track use only) and the squat setting would be ok for drag but that's not what my car is for.

Has anyone had it on the neutral setting or drift or drag and care to comment on the difference?

  • 1 year later...
Lazy-Bastard you were saying that you need 4 small pineapples for a drift/drag setup, where exactly do the two extra small ones go as i cant see them on the whiteline instructions page

Whichever way you set it up, you only need 4 in total. I think from memory the drift setup requires 4 small and no large but check the whiteline fitting guide

Whichever way you set it up, you only need 4 in total. I think from memory the drift setup requires 4 small and no large but check the whiteline fitting guide

just took a closer look at the diagram from whiteline, i didnt notice the there are small rings and small cut rings, so yes i need to 2 large and 2 small cut for a drift setup. thanks for the info

if they look like this then you need to remove the factory bushes.

If they look like this then you leave the factory bushes in place.

The alloy subframe bushes ARE to be used with the standard subframe bushes. They squash them down and prevent all movement of the rear subframe. The only bushes that require you to remove the original bush are replacement aftermarket bushes, i.e. Noltec

Pineapples are not actually replacement bushes, they are there to help tilt the subframe and resist movement.

And the smaller bottom bush does not require a cut in it at all, you take the nut all the way off, the other 2 at the other end will hold the subframe fine, just loosen them a little first.

Edited by salad
  • 1 month later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...