Jump to content
SAU Community

Recommended Posts

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

Damn... wish you guys had 4WD dyno, Lumpy did a Beautiful job on my tune for the 180, now the GTR is being tuned elsewhere.. Not my call though..

I hate living in the sticks otherwise I would be in for a tune after the next round of mods..

Damn... wish you guys had 4WD dyno, Lumpy did a Beautiful job on my tune for the 180, now the GTR is being tuned elsewhere.. Not my call though..

I hate living in the sticks otherwise I would be in for a tune after the next round of mods..

Why??

we can tune GTR's in 2wd mode. Has no adverse affect on either the car or the result..

Cheers

ken

A GTR is a full time rear wheel drive car with computor controlled split to the front and running one on a 4WD dyno means it must drive the front wheels the whole time its on the dyno and that is a very un natural situation for a GTR so dont panic about putting them on a 2wd dyno.

Damn... wish you guys had 4WD dyno, Lumpy did a Beautiful job on my tune for the 180, now the GTR is being tuned elsewhere.. Not my call though..

I hate living in the sticks otherwise I would be in for a tune after the next round of mods..

ha mate if you love your R like i do i would be sending it to the best tuner i know and Lumpy the man ,ran mine yesterday to check the afms(z32) that we installed and ran a lazy 529.4rwhp at 20psi even in the limited time we had to do so and just to watch the guy in action is impressive.

pete :D

ha mate if you love your R like i do i would be sending it to the best tuner i know and Lumpy the man ,ran mine yesterday to check the afms(z32) that we installed and ran a lazy 529.4rwhp at 20psi  even in the limited time we had to do so and just to watch the guy in action is impressive.

pete :P

do you mean you can actually watch it get tuned ? last time i was at hyperdrive ken shoo-ed my out of the workshop !

Yes for occ. health, safety and insurance reasons, everyone other than staff must be out of the workshop area in the designated viewing area. If something lets go, its bad enough mopping up the motor let alone the bodies!

I think Bart snuck a peek at the action on his way to either get another, or loose another bourbon.........

nah not the police

but you wouldnt read about it on freeway heading home a basic std s13 wanted a go well forgot it was still in 2wd and well it lit up at 115km for abit before we hose the p plate silly boy silly boy ,he must have got bit of a shock

ooppps this is bit off subject sorry

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...