Jump to content
SAU Community

Beginner & Regular Twilight Drfit Practice Febuary 16th


Recommended Posts

When: 6pm - 10pm, Wednesday 16th Febuary 2005

Where: Calder Park, Calder Freeway, Keilor

Cost: $80 per driver (includes one pit crew entry), Spectators $10

How to enter: All entries will be taken at the gate. Entries will be capped at sixty. Those who arrive early will have priority.

Car Requirements: Cars must be of a safe and roadworthy standard. They must have working headlights and break lights. Fire extinguisher and roll cage are not essential but recommended. Seat belts must be working and of a safe standard, harness’s permitted. All lose items must be removed from the car. It is recommended that you remove your front bumper to avoid damaging it.

Driver Requirements: Drivers must be licensed. Drivers must wear long sleeve top and long pants made of natural fibers e.g. cotton. Helmets must also be worn and are available for hire at Calder Park for $20.

Do not wear shorts and a t-shirt we know its getting warmer but this is for your own safety.

Passengers: Passengers are strictly not permitted.

Prizes Prizes will be awarded to the top three drifters on the night courtesy of Autobarn Sunbury . The top three drifters are decided by a top eight D1 style drift battle. The battle begins at 9:15pm presentations at 9:50pm.

Drift tyres will be available for sale and fitting at approximately $15 per tyre.

BEGINNERS

Remember the bottom section of the track will be open for practice for BEGINNERS ONLY, and we will close it when it gets dark (around 8.30?). Any beginners using this section of track are able to drive on the main circuit if they feel capable. Beginners will be instructed on how to drift by the Full Lock Drift Team/FLM Racing free of charge.

  • 3 weeks later...

It is not run like a "free practice"... there is a marshall starting people off at intervals to keep people apart.

Later in the evening the cars can get waved through closer together. Last time I heard there was a lane for people that wanted to drift in "tandem" for practice on that.

I did hear from Oran Park there were some problems with a few people who didn't really care about their cars so were making others a bit uncomfortable.

Yeah i went, it was an excellent night. The rain held off all night and there was heaps of cars, some people i felt were going a bit close to cars but like GOJIRA said it depends on peoples comfort level. It was only really in the tandem battles at the end of the night after all the corners people doing fishy rediculously fast down the main straight.

Yeah the R34 did have a lil mishap, didnt see the stack but saw it going onto the trailer, and i think it comes from Option House or something.

But was heaps of fun there was 4 R33 i saw including me, and quiet a few R32 two and four doors. Which added to the diversity of cars. Heaps of fun

yeah, the oh performance r34 blew the radiator when he hit the wall. bugga....

some good talent out there the other day, it was a shame the blue 180 decided to do a burnout through the pits....

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...