Jump to content
SAU Community

Recommended Posts

Hi all fellow Liners!

I just need some advise on mods for my Skyline.

I've had a guy give me a quote on a few things. Guy from Ovaboost Performance in Malaga.

Basically want to do some minor type stuff, know absolutely sweet f all about these things and really want to learn as much as I can.

What I got quoted on was:

Intercooler,

3" Dump pipe (cause it's stock from the cat back)

Manual Boost controller &

SAFC.

This according to him would get me about 250rwhp. Think it involved turning up the boost of the turbo alittle. The approximate cost was $2500, which includes fitting and tuning.

At this stage I don't want to go overboard, but maybe down the track I will change the turbo as well.

Just want to know what you guys think, recommend etc? Also I've been told it's better to have and Auto boost controller.

Cheers,

Pulp.

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/
Share on other sites

I'm currently hitting 228hp with a front/dump turbo back exhaust and an air filter. boost is standard.

front mount/safc/tune should give me more than an extra 20HP, so you'd hopefully hit 270hp. although some people have said new injectors might be needed after 270hp.

good luck.

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1177715
Share on other sites

where do i get an intercooler pipped and fitted for $1000 ?

i would forget the safc and put the money into a better electronic boost controller because you only have limited boost to work with on the stock turbo and you dont want to waste 2 psi as a spiking buffer .

Or just forget about boost control , youll probably hit about 10psi with a 3inch exhaust anyway and then put the money towards a powerfc which is a full replacement computer and much more programable than the safc.

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1178266
Share on other sites

Thanks guys!

Damn I thought that my quote was sounding good!

I hope I'm not getting ripped!I'll do some shopping for sure.

arkon, you were saying about not using the SAFC, does the electronic controller adjust to our fuel type etc too? Cause the guy was telling me that the SAFC did this. I don't know if I really want to go too much into upgrading the computer (PowerFC), just gonna do a little at this stage.

Sorry still learning all these things!

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1179030
Share on other sites

adjusting to our fuel type is not really required the stock ecu will do just fine on 98 octane fuel at the tune level you are looking at .

an electronic boost controller will do the same thing as the manual boost controller , ie control boost . however it does it with more accuracy and is controllable for hi and lo settings things like that .

the problem with the safc without going into to much technical stuff is it doesnt do that much so you wont find a huge gain with it now , maybe 15-20kw and later on it wont offer the level of tuning required to support more serious mods . so for the level your at the stock ecu will be fine

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1179277
Share on other sites

I see, now things starting to make sense!

I was told by someone the same thing about the controlling of the boost, but wasn't sure if it would be necessary. I think I'll go back and get him to give me another quote with the electronic controller. I don't want to have to go back and make changes later cause I wont be happy.

Thanks again Arkon! Great help.

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1179288
Share on other sites

Hi pulp,

Do you want to go faster or just have a 250rwhp dyno to brag about?

If the answer is faster;

* S-afc II is a good move. Buy one second hand for around $400 + $100 to tune.You can turb around and get most of your money back if and when you need a PFC.

* Manual bleeder boost controller. Nothing wrong with them for a factory turbo. Don't waste money on an electronic one. Aim to make good power at around 10-12psi, this is enough on the factory turbo to get you a low 13.

* Consider the front mount upgrade carefully. Pick the correct size based on your final application. If you are going to be happy with the factory turbo then reconsider getting one, it won't stop you doing low 13 quarter mile passes. As a note consider how many people can't go that quick with a front mount on the stock turbo (there are reasons why).

* exhaust improvements are a great idea. go for it.

Other things to consider...

Pineapples $100 and gets you more traction.

Adjustable exhaust cam gear. Retarding the timing on the exhaust cam nets you some earlier boost and about 10hp right through the power band. $200 DIY.

Lightweight flywheel (assuming you don't have an auto) .Along with an upgraded clutch this is worth putting in to experience increased acceleration (I gained almost half a second drop over the 1/4).

The forced induction section has plenty of good info so you don't have to reinvent the wheel.

Learn a little and you won't become a 'bolt on boy'. Instead you go faster for less effort. It's fairly easy and cheap to get low 13's out of an R33 gtst, you just need a little 'good' information. There is plenty around.

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1182063
Share on other sites

Hi Rev210,

Yes the faster factor is what I intend on achieving.

With the front mount option, I do intend on upgrading the turbo down the track so I think getting one installed would be the way to go.

I think it's a great idea what you said about the SAFC II and saving up for a PFC later. I think this guy quoted me $660 + $110 to tune.

Although, considering I want to put a bigger turbo in later, do you think I should get the electronic boost controller now?

I will head off to the forced induction section and have a read I think!

Thanks very much for the info mate!

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1182687
Share on other sites

you can import a brand new SAFCII from greenline or nengun i think it was for $450 landed in under 2 weeks.

My friend got his Power FC from Greenline for $1100 landed in less than 2 weeks so you won't need to search around for 2nd hand.

also look into getting more traction as the pineapples was mentioned. the more of that power hits these ugly bumpy streets we got here the better but you need to be able to control that power.

Link to comment
https://www.sau.com.au/forums/topic/62496-advise-on-mods/#findComment-1185412
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...