Jump to content
SAU Community

Recommended Posts

Hey there people!

I was in All American today and saw this awesome looking R32 GTR for sale!

It was originally from Vic & Qld, and had a write up in the HPI magazine No 40. Number plate was BNR - 32. It had 430kW and has had little more mods done to it since.

Her are the specs:

Vielside Evo (Blister) Widebody kit,

Panasport 17x10 17x12 G7 C5C2 Rims

Dunlop Sport 275/40 315/30 typres

Trust T88-34D Turbo kit wit ext wastegate & manifold etc

Hks 1000cc injectors

Hks Oil Cooler

Apexi PFC wit hand controller

Splitfire Ignition Coils

Os Giken Triple Plate

Kaaz rear diff

Hks GT bar & plate Intercooler

Field Torque split controller

Defi BF Boost gauge, exhaust temp gauge

Veilside steering wheel

Apexi N1 Coil over Sus.

Veilside Exhaust

N1 Headlights

Grex twin remote oil oil filter rellocation kit

coolant swirl pot

Hks Cam gears

Twin gauge pillar pod on dash.

greddy twin inlet pipe for turbo

Trust Airnx air filters

Z32 air flow meters

Trust gear knob

Nismo 320Kph dash.

Pioneer in dash touch screen DVD player

Clarion 12" sub with amp

Car has made 480hp @ 4 wheels at 1.2 bar of boost.

Don't know if these figures are correct, but anyway.

He is asking $69,999 for it!!

Go check it out, worth a look!

Pulp.

Link to comment
https://www.sau.com.au/forums/topic/63088-519rwhp-r32-gtr-for-sale/
Share on other sites

Yeah seem a bit expensive but I think devil's right, I think maybe a limited model.

Devil, I think he did actually! I love Mustangs myself, fastback 65 model is what I'm after.

Although I think the 56 Corvette! Spider model maybe? is the best looking one! Same as the one in True Lies with Arnold & Jamie Lee Curtis.

Holy Crap!!!! Price has jumped up 20g's since Nathan tried to sell it!!!! ha ha ha ha And considering it didn't sell at 52k what makes ya think it'll sell at 70k???????

What a rip.. Also remember that the engine is still stock internals so for 70k thats f*cking stupid... The motor that was in it in the HPI feature was taken out before it came over here...

Holy Crap!!!!   Price has jumped up 20g's since Nathan tried to sell it!!!!  ha ha ha ha  And considering it didn't sell at 52k what makes ya think it'll sell at 70k???????

What a rip..     Also remember that the engine is still stock internals so for 70k thats f*cking stupid...   The motor that was in it in the HPI feature was taken out before it came over here...

OHHHH! it was taken out hey? Well then, that's just shite! Definately not worth it then! So do you think it really has 519rwhp?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...