Jump to content
SAU Community

Recommended Posts

How *involved* is the engine removal on an RB26DETT.... ? Looks a tight fitting s0d... any chance of a quick run-down of whats involved and possible pitfalls? Any *special* tools from dealer needed etc? :Bang:

I want to remove the bugger to fit a larger capacity sump, good look round the turbos etc and maybe dress the old girl up a bit.

If this works out *too* difficult might have to pay labour at a local shop... :goddam: and to be honest it would be good to see the thing out in case I need to do it again in the future... :alcoholic .. how many hours approx? :kick:

Doing a search on it at the mo but any links on this would be sweet :)

Oh yea, I'll be doing this with a standard engine hoist, hope & some beer :D

.

..

...

.....

.......

......... :)

Link to comment
https://www.sau.com.au/forums/topic/63330-rb26dett-engine-removal/
Share on other sites

ummm....personally I found it a crap job and would leave it until she blows....rebuild isn't that much more expensive if you need to fix broken stuff as well....

no special tools as such, the two things I remember causing the most trouble where the top gearbox bolts which need 4 x 1' extensions to get at, and the starter motor bolts which need 1" long fingers and a stubby ratchet to get at :P

There has also been a good thread about whether to take it out under or over, with or without gearbox, try a search.

It took us about 5 hours from memory. 1 person knew what they were doing, a couple watching from chairs with beers, and me getting in the way.

ummm....personally I found it a crap job and would leave it until she blows....rebuild isn't that much more expensive if you need to fix broken stuff as well....

no special tools as such, the two things I remember causing the most trouble where the top gearbox bolts which need 4 x 1' extensions to get at, and the starter motor bolts which need 1" long fingers and a stubby ratchet to get at :P

There has also been a good thread about whether to take it out under or over, with or without gearbox, try a search.

It took us about 5 hours from memory.  1 person knew what they were doing, a couple watching from chairs with beers, and me getting in the way.

The beer to talent equation....! will try another search thanks! :)

I have done it before , i prefer to pull out as 1 unit engine + box , i find it easier .

I dont know if your engine crane will lift high enough for the 2 units tough , i lift with a chain block . you will need your hoist to be able to lift about 2.1 meters ( from the floor to the hook of your crane ) . Others undo the box and drop it under the car and like in Duncans case undo the box and leave it there .

whatever you do you will need to tilt engine box to get to the top box bolts and to make it easier to undo the top starter bolt . I leave everything on the engine , just undo the air comp and secure it on the rail do the same with the steer pump .

Just the normal stuff , undo everything , take radiator out drive shafts , undo all hoses take airbox out .

hook your chain on the front and rear hooks or use a strap around the engine .

One person you will need almost all day and then a helper when you lift it out .

I have done it before , i prefer to pull out as 1 unit engine + box , i find it easier .

I dont know if your engine crane will lift high enough for the 2 units tough , i lift with a  chain block . you will need your hoist to be able to lift about 2.1 meters ( from the floor to the hook of your crane ) . Others undo the box and drop it under the car and like in Duncans case undo the box and leave it there .

whatever you do you will need to  tilt engine box to get to the top box bolts and to make it easier to undo the top starter bolt . I leave everything on the engine , just undo the air comp and secure it on the rail do the same with the steer pump .

Just the normal stuff , undo everything , take radiator out drive shafts , undo all hoses take airbox out .

hook your chain on the front and rear hooks or use a strap around the engine .

One person you will need almost all day and then a helper when you lift it out .

If you dont have a 3/4 rattle gun undo the crank pulley before you take it out , it will be very tight , use your starter to undo it .

re the bolt at the front of the crank we got it off OK with a 1/2 breaker bar and big arse socket, and a pry bar holding the flywheel in place. Were we lucky / do you normally have a heap more trouble?

No i don't have any probs at all , i just use a 3/4 " rattle gun if the engine is out .

I have used your method as well with a 3/4 " socket and a home made special tool to hold the flywheel from turning .

When engine is in the car you cant use a rattle gun so i use the starter , its very easy .

You have to be carefull when you use a pry bar / screwdriver on the ring gear , you could break a tooth .

The tool that i have made grabs a few teeth .

Guest two.06l
How *involved* is the engine removal on an RB26DETT.... ? Looks a tight fitting s0d... any chance of a quick run-down of whats involved and possible pitfalls? Any *special* tools from dealer needed etc? :Bang:  

I want to remove the bugger to fit a larger capacity sump, good look round the turbos etc and maybe dress the old girl up a bit.

If this works out *too* difficult might have to pay labour at a local shop...  :goddam: and to be honest it would be good to see the thing out in case I need to do it again in the future...  :alcoholic .. how many hours approx?  :kick:  

Doing a search on it at the mo but any links on this would be sweet  :)  

Oh yea, I'll be doing this with a standard engine hoist, hope & some beer  :D

.

..

...

.....

.......

......... :(

We drop them out underneath in one unit a'la Peter Hall from adelaide. It is easier in the long run and less scraped knuckles.

yeah sorry the Pry bar is between fly wheel bolts....just chuck a couple back on.

perhaps its time for a compressor....

and yeah Stacey we've tried the engine out the bottom as well, it was probably easier, but we had trouble with lifting the car high enough on the engine hoist? do you have a full hoist instead?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
    • Continental have consistently beaten the absolute shit out of every other performance tyre in Wet/Damp/Cold conditions and give up a little bit of time (half a second at most) in the dry. Almost like it's engineered for German conditions or something. I'd def give those a try.
×
×
  • Create New...