Jump to content
SAU Community

OMG WTF 15yr rule GOOOONE!!!!1!!one!!11


Recommended Posts

L11/05

Monday February 7 2005

MINISTER ANNOUNCES CLOSURE OF CAR IMPORT LOOPHOLE

A plan to tighten Australia’s vehicle importation laws that will reinforce motor vehicle safety and emission standards was announced today by the Minister for Local Government, Territories and Roads, Jim Lloyd.

“The Government is closing a loophole that has enabled mainstream cars over 15 years of age to be imported in commercial quantities, and not subjected to safety and emission certification,” Mr Lloyd said.

“Importers of these cars were using an exemption that allows hobbyists and enthusiasts to import classic and historic cars. This exemption exists as these vehicles generally perform low mileages and are limited in numbers, and therefore represent a minimal risk to overall Australian vehicle and safety goals.

“Without such an exemption, the private importation of these types of older, collectible cars would become uneconomic.

“The closure of this loophole will only apply to those vehicles which do not fit in the classic and historic category, thus preserving the ability of hobbyists and enthusiasts to obtain older classic cars and historic vehicles.”

Mr Lloyd said a transitional arrangement would be provided for other vehicle importers who had current commitments to bring in vehicles under the old rule.

“The changeover is being introduced gradually, to allow importers and consumers time to react to the revised focus of the exemption,” Mr Lloyd said.

Under the new rule:

Vehicles manufactured before 1 January 1989 may be imported without restriction.

Vehicles built during 1989 (or later) will need to qualify under the Registered Automotive Workshop Scheme (RAWS) and will need to be certified as complying with Australian Design Rules (applicable at the date of manufacture). To qualify under RAWS, vehicle models must meet the specialist and enthusiast criteria.

The buffer period (between collectible vehicles and mainstream vehicles) will be gradually extended over time – up to a maximum of 30 years.

A transitional arrangement will also be established. Those importers who have already made a financial commitment before today on a vehicle manufactured in 1990 intended for future import, will be allowed to bring the vehicle into the country under the old rule up to the end of December 2005.

“This new rule will re‑instate a ‘level playing field’ within the industry. Vehicles supplied to the same market will be subject to the same regulatory environment, substantially reducing cost pressures on mainstream businesses,” Mr Lloyd said.

Media inquiries:

Mr Lloyd’s office: Fiona Telford 02 6277 7060

Technical inquiries:

Department of Transport and Regional Services: Justin Bryan 02 6274 7426

OMG.jpeg

OMG!! The pope is reading this thread!!

never seen him so enthusiastic in my life....hes keen for a high hp gtr........thats never gonna happen now. His realised this and thats why hes now in hostpital, theres not much left to look forward to for him.

Sorry, this thread wasn't really constructed for serious conversation..

I motion to the council that it may be removed.

Motion granted... This thread has served us well these past 12 hours and hencewith shall be presented with a gold padlock...

Guest
This topic is now closed to further replies.


  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...