Jump to content
SAU Community

OMG WTF 15yr rule GOOOONE!!!!1!!one!!11


Recommended Posts

L11/05

Monday February 7 2005

MINISTER ANNOUNCES CLOSURE OF CAR IMPORT LOOPHOLE

A plan to tighten Australia’s vehicle importation laws that will reinforce motor vehicle safety and emission standards was announced today by the Minister for Local Government, Territories and Roads, Jim Lloyd.

“The Government is closing a loophole that has enabled mainstream cars over 15 years of age to be imported in commercial quantities, and not subjected to safety and emission certification,” Mr Lloyd said.

“Importers of these cars were using an exemption that allows hobbyists and enthusiasts to import classic and historic cars. This exemption exists as these vehicles generally perform low mileages and are limited in numbers, and therefore represent a minimal risk to overall Australian vehicle and safety goals.

“Without such an exemption, the private importation of these types of older, collectible cars would become uneconomic.

“The closure of this loophole will only apply to those vehicles which do not fit in the classic and historic category, thus preserving the ability of hobbyists and enthusiasts to obtain older classic cars and historic vehicles.”

Mr Lloyd said a transitional arrangement would be provided for other vehicle importers who had current commitments to bring in vehicles under the old rule.

“The changeover is being introduced gradually, to allow importers and consumers time to react to the revised focus of the exemption,” Mr Lloyd said.

Under the new rule:

Vehicles manufactured before 1 January 1989 may be imported without restriction.

Vehicles built during 1989 (or later) will need to qualify under the Registered Automotive Workshop Scheme (RAWS) and will need to be certified as complying with Australian Design Rules (applicable at the date of manufacture). To qualify under RAWS, vehicle models must meet the specialist and enthusiast criteria.

The buffer period (between collectible vehicles and mainstream vehicles) will be gradually extended over time – up to a maximum of 30 years.

A transitional arrangement will also be established. Those importers who have already made a financial commitment before today on a vehicle manufactured in 1990 intended for future import, will be allowed to bring the vehicle into the country under the old rule up to the end of December 2005.

“This new rule will re‑instate a ‘level playing field’ within the industry. Vehicles supplied to the same market will be subject to the same regulatory environment, substantially reducing cost pressures on mainstream businesses,” Mr Lloyd said.

Media inquiries:

Mr Lloyd’s office: Fiona Telford 02 6277 7060

Technical inquiries:

Department of Transport and Regional Services: Justin Bryan 02 6274 7426

OMG.jpeg

OMG!! The pope is reading this thread!!

never seen him so enthusiastic in my life....hes keen for a high hp gtr........thats never gonna happen now. His realised this and thats why hes now in hostpital, theres not much left to look forward to for him.

Sorry, this thread wasn't really constructed for serious conversation..

I motion to the council that it may be removed.

Motion granted... This thread has served us well these past 12 hours and hencewith shall be presented with a gold padlock...

Guest
This topic is now closed to further replies.


  • Latest Posts

    • Update 2: Today I'm f**king pissed. Some of you probably saw my thread that I opened shortly after joining this forum, "urgently need expert/experienced opinion", in which I discussed the possibility of a porous RB26 engine block which I also found hard to believe. Currently both turbos are out since the shitty braided line that was installed by whoever fitted the GT28 turbos leaked oil onto the exhaust. Today while working on the cam covers to put new gaskets and half moons in, I cleaned the side of the engine block with brake cleaner. Some time later I saw that it was still glistening with oil or coolant so I dried that off. But it was wet again shortly after. Verdict: I'm royally screwed. What you can see here (hopefully, despite shit resolution), circled in red, is a crack above the turbo oil feed. Extent is a few cm long and basically goes from #3 cylinder wall to #4 cylinder wall. It slowly lets coolant through, even without any pressure behind it. I am absolutely dumbfounded as to how this crack even formed, especially since it isn't along the cylinder as it usually is but rather a horizontal crack. Probably a few cm in length. Not sure on how to deal with this issue right now. Most likely, the only true fix is a new engine block, and even a relatively well done temporary fix requires at least a full engine teardown. Neither of those really fit my timetable right now, the car has been in my buddy's garage long enough as it is. I'm open to suggestions, but I'll be looking into ordering a new 05U block soon so I have one ready for the coming year, or whenever the current block inevitably fails fully. (Most likely once the crack reaches one of the frost plugs) I think it'd be a waste of money and time to rebuild the engine with this block. Oh and I found a rust hole on the side pocket of the trunk, which someone covered up with sealant goop, a piece of number plate and bodywork filler. Fun times. So far for every issue we fix we just find a new one that is arguably worse.
    • I have not found this no. I put one back on a couple days ago with no drama. I agree they are tight, but no need to remove anything. 
    • That is gates blue racing belt
    • Anyone found gates blue racing to be extremely tight/ almost impossible to install without moving the exhaust gear
    • Hello am apex am new here and also thanks for helping registering the forum 
×
×
  • Create New...