Jump to content
SAU Community

Recommended Posts

Its not so much the power but the amount of Air that it can measure. For example a HKS GT-RS will make a certain power level at 14 psi and a standard turbo will make a bit less power. What I am trying to say is that I think the rb25 AFM will max out at about 14 psi. Now depending on what turbo you have your power levels at 14 psi could be anything from 180rwkw upwards.

If your rb25 has a stock turb then the stock AFM should see you to about 200 rwkw...

hope that makes sence :)

my airflow meter maxed out at 12psi and i was making just over 200kw

there are alot of things that you have to take into acount

you have to remember that hot wire air flow meters work by heating the little wire in side, when air passes over it, it changes the resistance in the wire so it takes more voltage to heat it and thats the signal that is send back to the ecu. once the voltage reaches 5.13 volts it cant heat the wire anymore and that is when you are maxed out

air density(temperature) plays a big part in this as colder air will cool the wire easyer

that i why mine maxed out at around 12psi and some of you guys can run up to 14 psi without a problem

i hope this has helped you

what symptoms would you have if your air flow meter was being "maxed out"

like if you didnt have an FC with commander telling you exactly whats going on. how could you tell?

Cheers

if your running a standard ecu it feels just like your boost cut and if you havnt hit that yet, it feels like your going to be thrown though your front windscreen, its a very sudden jolt. thats the best way i can explain it

I changed to rb20/25 afm's on my GTR becuase the std ones ran out of head room. I'm running 2530's at 1.2bar with rb25 afm's(same as rb20) and I more headroom then I need . Much cheaper option then z32's and the rb ones just plug straight in .

that's what he want's to hear :cheers:

to others he's talkin twin rb20/rb25 afm's on a gtr

This is from Sydneykid

Rule of thumb for Air Flow meters RWKW & Engine BHP

------ ---- OD ---- RWKW ---- RWKW ---- BHP ------ BHP

No of AFM's ---- ------- 1 -------- 2 -------- 1 -------- 2

RB26 ------ 65 ------ 149 ------ 299 ------ 271 ------ 474

RB20/25 --- 80 ------ 226 ------ 453 ------ 376 ------ 683

Z32 ------- 80 ------ 255 ------ 511 ------ 415 ------ 763

Q45 ------- 90 ------ 302 ------ 605 ------ 479 ------ 890

Your Engine warning light will also flash in a particular sequence when your AFM maxes out. This is often mistaken for knock... I am not sure what the 2 different sequences for knock and AFM Max out are though...

Is their a way of checking if the stock AFM is maxing out? without using an aftermarket ECU?
Is their a way of checking if the stock AFM is maxing out? without using an aftermarket ECU?

Sure can mate. if you have the car on the dyno the output voltage can be checked using a multimeter. anything over 5volts and the AFM is near max. infact with a pin out diagram you may be able to check what voltage the AFM is sending to the ecu (thus not needing to check it in the engine bay), this way you could check it on the street/strip instead of having to use a dyno.

  • 3 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...