Jump to content
SAU Community

Recommended Posts

Ok I blew my RB20DET 5spd man box at local drags using slicks

Whats the best way to get strengh so this wont happen again

now im contemplating in either using a RB25DET 5spd as they are supposed to be stronger than the RB20DET unit, Also will my RB20 clutch (exedy HD) be ok to use with the RB25 box??

or is there any auto boxes that are strong that will work, like RB20 or RB25???

I just dont want to go back out again and destroy another gearbox on slicks...

Do in this order

1.Bin RB20det box

2.Laugh at how small it is

3.Find RB25det box

4.Admire it's fatness and giggle like a school girl

But seriously it will bolt to the RB20,use the RB20 flywheel/clutch,you need to mod the gearbox mount with some flat bar,use R33 slave,shifter and the yoke or vlt yoke.Speedo,if it's cable I hear a cut down?vlt sender could work

How much power are you making, and what sort of rpm did u decide to dump the clutch at? Are you wanting a straight bolt up gearbox, im guessing you have an rb20 in a vl? what about the mx7? rb30et gearbox. You could always get anything, just depending how much money you want to spend. You could go all out and get a tremec tko 6 spd :rolleyes: haha

MX-7's are weak as shit too.

they are soo old they just shatter. I've seen heaps die here in Vic.

Mine, and a mates.

Get an RB25 box and you'll be fine. Just make sure you get a yoke with it.

whats the point of a yoke when they are pressed and seal uni joints and have to be scrapped???

I got a yoke with my 5psd but when i took it to the driveline place they said they couldnt use it. I think i ended up getting a suitable Mark William "V8 Supercar spec" yoke with replaceable uni joints for SFA

you can use em. I need one for my 25box to fit to my car.

tierh that or its the driveshaft... so i got both. :rolleyes:

been a while since my workshop has done a 25 box... as usually cars aint POS's like mine... hehe

i am in the middle of the same gearbox convert. All boxes seem to be from $1500 to $2000. The yolks as far as i know can be blended with the standard uni. I have a friend who did this convert and thats what he did and it seemed to work. Not 100% sure but thats what he said.

Are you guys still talking about a second hand box???

Why bother putting in a box that has had the k's wound up on it already, and god knows how that was treated. Why dont you just get a box and rebuild it properly with all new bearing cogs, the lot. Of course strengthened parts. Might cost more, but hey, for that peace of mind ...

and mx7's arent that bad, i had a vlt gave them thing so much shit, was on the way out when i got it, and was still going 18 mths later. with plenty of flat changes. haha

From what I have heard they are the same strength but the RB25 Box has much better designed syncros.

Yeah, I would agree with that completely, thats what should have been said in the first place by the other users.

;)

Tizzle,

32702 - 02G17 pinnion assembly

If they ask what model car say Navara. shouldnt cost more than $26

I got mine from Metro Nissan at Windsor... Those guys are complete wankers in my opinion.. Good luck ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...