Jump to content
SAU Community

Is it safe to drive your car with out the mud guards underneath the engine bay?


Recommended Posts

Well i lost the entire piece whilst driving so i have nothing protecting the engine bay from mud or water.

Should i find a replacement or would it be fine?

i dunno

i took off the bottom piece for the oil change

took off the ones in the guard due to scrubbing

might put them back on later after i bang in the grooves with a hammer

most people that install aftermarket fron bars do not have them on

i dont havnt for a month or so also drove through flooded road in order to get home and it went fine.

If you mean the intercooler guard... Mine fell apart and started scraping on the road... So i took it off and no problem so far. (2 months though)

LOL

Same as mine i fut the GTR bar on and they were to short so they would scrap the road, they got reduced further in size after the road gave them a sand job but a couple cable ties fixed that!!! :)

LOL, love the stories. Mine fell off because i drove around with no front bar for 2 days as it was getting a respray. Whilst driving on the freeway i begain to hear some scraping noise but i ignored it for a while and then i heard some thing clatter near my guards and before i knew it i heard a loud bang and i looked in my rear view and saw the whole thing fly off. I wanted to go back and retrieve it but there was a highway patrol coming in the opposite direction and so to avoid any confrontations' i decided to let it go (code red). Not happy but since you guys seem to be going fine i guess I'll join the club! : )

I need one of them for my r33, the only problem of not having one is that your engine bay gets really really really really dirty.

EDIT: which flaps are we torking about, the one that behind the bumper? or the one that is under the engine?

I fiited an aftermarket frontbar and soon after I lost all three trays (under engine and both wheel arch ones) at a circuit with a Porsche Carrera 4 inches behind me. Huge bang (thought he'd hit me) followed by lots of light flashing :D

Ronin you're going alittle overboard however I did swap my std nissan tray for a nismo 1 and picked up around 6rwkw... true story

ok ok, it didn't fall out.

it's lucky i had the intake plenum zip tied to the nismo strut brace; it held the motor nicely :(

w00t, I have cableties holding the corners of my front bar off the road. Best. Invention. Ever.

Hey thats what ive done until i go and get them replaced. It looks funny though, bits of string holding the tray from scraping on the road.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...