Jump to content
SAU Community

Recommended Posts

$800 is very very fair for a quasi fiberglass/faux carbon bonnet.

Don't pull prices out of your rear end without some kind of justification.

Other tuners can also do a good job for example at UAS.

T.

How about you read posts properly before you jump in to correct people Tony?

Link to comment
https://www.sau.com.au/forums/topic/65980-croydon-gtr/#findComment-1231608
Share on other sites

How about you read posts properly before you jump in to correct people Tony?

Oh because I'm the only one to make that mistake...

>allright, thx a lot guys for your advices.

>does anyone know where can i get the carbon fibre bonnet for R32 GTR?

person 1

>have a look here

>www.nismo.com.au

person 2

>you think that's expensive????

>try buying a proper carbon fibre bonnet

person 3

>seconded. Adam and Ben certainly know what they're doing.

I apologise otherwise.

About what CRD charge... sometimes I hear it's $600, $700 and up.

Ask what others charge for a dyno tune. Just because CRD are alleged to be the best, doesn't mean others aren't as professional.

T.

Link to comment
https://www.sau.com.au/forums/topic/65980-croydon-gtr/#findComment-1231730
Share on other sites

You gotta ask yourself what you want to achieve. It's not about achieving the highest rwkW.

Some people believe that perhaps a dyno tune then a follow up road tune is what's needed.

You can spend a good half of a day doing this. Also you might want someone who has access to the laptop s/w instead of just the hand controller.

T.

Link to comment
https://www.sau.com.au/forums/topic/65980-croydon-gtr/#findComment-1231905
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...