Jump to content
SAU Community

Recommended Posts

I purchased 2 turbos off Doughboy recently that had been rebuilt by Precision turbos in Sydney.

When I got the turbos to me they looked fine, booked it in down at the workshop and my mechanic rang me a few hours later and said he had some bad news. Said both turbos had a hairline crack on the exhaust side where the actuator lid open/closes, on the surface and also down into it.

I asked for my money back but later got an email saying he had rang both Precision and GCG turbos and both workshops apparently said that is normal and they wont get any bigger, and wont affect the performance of the turbos as the lid seals the flow.

My mechanic also said he rang 4 people and 2 said its normal and will be ok, and 2 said they wouldnt go near em.

My mechanic said he could weld the break and grind it back etc, but being cast iron and always moving/changing temps he said it would just cause a crack next to the weld anyway.

End of the day DoughBoy wasnt going to give me my money back so I have no choice to fit them anyway, but what i want to know is will they be ok and will they be ok for a long time, or will the cracks eventually split too big and be forced to fix them up?

I thought it was strange a turbo workshop that apparently charged $2000 to rebuild the turbos didnt even bother fixing the cracks in the first place...

Has anyone had any experience with this sort of shit happening on turbos?

If 4 out of 6 people say they will be all right? Unless your mechanic is a ticketed welder then id say do not weld them.

If your mechanic has experience with welding housings, then he is your mechanic. But id be worried about the type of welding he is doing, the wire/ he is going to use, will be gouge the welds, how will he know what is sufficient penetration etc etc???

Having fair a amount of experience with boilers/burners and all the cast items used in these, its not unusual for castings to have what appears to be hairline cracks on the surface of their bodies. If you have to look twice to see the cracks then i think you are in the clear.

Sure the things get hot, but they are not under any mechanical load or under pressure. So the cracks will stop and grain boundaries and not propogate thru the whole casting...that would be considered catastrophic failure...and according to the calcs you can punch for cyclic heat loads would be akin to winning lottery ... not going to happen in this life time.

If you rang a place like AMEC, (materials science/testing experts) i reckon they will tell you what i have told you, but charge you coinage for the test to verify what they would be pretty sure of. Hell if you want it tested but dont require any NATA certificates for it, they will be able to confirm what 4 out of 6 people have told you, and what i suspect based on experience in the pressure piping/vessel industry.

Hope that helps?!?!?!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...