Jump to content
SAU Community

Recommended Posts

I'm no longer interested in the DFA for meantime Shan, I might get it later on in future though. And my friend is switching his order from the DFA to EBC. So the order (including my friends) is now:

3x Independant Electronic Boost Controller

3x Hand Controllers

3x Cables

  • Replies 218
  • Created
  • Last Reply

Top Posters In This Topic

does the HC have light? and no writing? if so then do what newkleer said. The trimpot is located near the 25 pin thing to the left its blue and white, turn clockwise about 45 degrees. If the hc has no light at all then i don't know.

i'll try that out shortly......also ..i checkd the soleniod and tht works with direct power.. but when i hook it up to the board as per instructions..nothing happens.. ive got my jumpers set to suit ..as its a normal open unit.

when i turn the ignition on .....the solinoid ..being normally open should shut with power going to it.... its not doing that at all.

but ..at the same time ..i should have power to the HC.....but again ..its not doing that at all... trying to find my multimeter at the moment to track down the weak link

Matt

i havent either, but wasnt expecting till early next week (given monday was public holiday, so sending out on sat would be like sending out on tues)

Finished my DFA today, did everyone wire the link between the crystal capaciter thing and the hole near the plug?

If you are talking about the 20Mhz crystal, yeah, I did. It's jsut to ground the metal case of the crystal but in all my years in electronics, I haven't yet found why they do this. I'd say do it anyway. :)

this one's for the guys waiting for a mail delivery... I've been sent back all the parcel post packages I sent out because I hadn't signed the dangerous good disclaimer :rolleyes:

anyways, after talking to the guy at my postoffice I've organised for them all to be delivered via express post (24 hour delivery) so you should all recieve your packages tomorrow for sure.

Hey guys ive just noticed something on the IEBC pcb thats a bit confusing, the small link link5 is shown in the wrong position on the printed circuit board... Make sure you follow the overlay diagram not the picture and not whats printed on the pcb.

And yeah i earthed the crystal things... i dont think thats documanted very well either, i suppose its not that important to do it.

hey funky jsut wondering if it's time to start the new group buy, or at least get peoples intrest.

awesome job mate

cheers mark

i'll start another thread for group buy #2 shortly... i've just sent off the last of the first batch (hehe good one NewKleer)

this thread's a bit too long for people to browse thru n stuff. But has lots of good reading for people buying... I'll summarise costs in the new one and you guys can put down what you want. Once the necessary numbers are up (which should be within a few days) I can put in a second order.

next time I'll just cut the crap and just mail out using 24 hour delivery satchels, they're much more effective and they can hold an ebc, dfa, cable, book and handcontroller... just.

Did everyone get fragile stickers on their packaging, because I asked the postie to stick em on.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...