Jump to content
SAU Community

Recommended Posts

Well my girlfriend was trying to convince me for some time now to let her drive my R32, and i kept getting out of it with all sorts of excuses. She just wouldn't take NO for an answer.

Well she finally convinced me, and 5 minutes later, she hit the gutter. She wasn’t going fast maybe 20 km/h so I didn’t expect much damage.

I tried my best not to get upset and even after assessing the damage on the wheel i was still ok, but then I started driving the car home and the steering wheel is off centre. GRRRRRRR.

So what could possibly be damaged?

Would a simple 4 wheel alignment fix the problem?

Can any place like Peders do the wheel alignment on a Skyline or maybe i should go somewhere else?

Also, can they check if my steering wheel is properly aligned coz I’ve been having a few HICAS issues. The steering sensor is not on 12-6 o’clock . It’s more like 10-4 o’clock.

I know f**k all about suspension so any help will be appreciated.

A Skyline is a lot diff at the front than a S13 having a double wishbone front susp setup. There is also a good chance that you've also bent a control arm. Take it to a more specialist suspension place so they can measure everything up then get the alignment done.

yeah id say ure alignment is just knoocked out...........

walk up to your girlfriend and slap her with the bill !

then tell her she is too only sit in the passenger seat and do nothing else!......

if u do this she will neva ask about the car and it wont come up in conversation.....hahahah

You won't just knock the alignment out.

Something under there is bent, simple as that.

Either make her pay or kick yourself for taking the risk.

Back to the car though, go get a 28 point inspection at pedders or any other suspension shop for the full report.

Geezzz....glad i never let my gf drive my car.....just confirmed my fears of doing so. but yeah....in regards to the car, id say its not just an alignment issue, how fast and hard did she hit the curb....must of been a bit of an impact to cause suspension damage.

Thanx for your help guys.

I think i'll just take it to the Peders 28 point obligation free inspection to see if they can pin point the problem and I'll take it from there.

If it's a bent steering arm, can they fix it or it has to replaced? Cost?

I've learnet my lesson but I wont be taking any money from her. It wouldn't be nice but she is much nicer when she's feeling guilty. :)

My other half has had quite a bad run with my cars in the past. :)

Car Number 1.

My Super clean N/A VL 5speed.

It was so clean it was like it just rolled off the factory floor.

I let my other half drive, she was learning at this stage.

Joel: Sit back, there's no need to sit so close to the car in front.

Julie: Its ok I won't hit him.

Joel: Its just a matter of time.

At that moment Julie looked over her shoulder to check her blind spot.

arrrrggg the car in front broke and we cliped his rear bumper ripping off my plastic fantastic VL front bumper. :) No body damage luckly.

Car Number 2.

Almost bran spankin new VS 5ltr 5speed Exec FE2, SRS, ABS, IRS Commodore.

I only just got the car back from a few mods.

I spent a lot of $$ on that car.

Full Whiteline suspension kit, Adj. swaybars the whole lot.

3.5" exhaust (single straight through muffler that was no bigger than a shoebox), pacemaker extractors, mild cam and had the ecu done. (Still made stuff all power) lol

I was replacing Julies parents brakes on their VN commodore.

Julie: Joel, I'm going to wash the car.

Joel: Yep ok.

Julie walks over to the second drive way and starts the VS.

The sweet V8 brup brup brup I hear.

Next minute I hear the VS still idling but slowly getting further and further away. :(

I look up and see Julie starting the car behind the VN that was in the drive way. At that moment I hear an almighty BANG and a distant sweet brup brup brup sound. :)

OMFG I thought.. I looked across the road.

The damn car had rolled down the drive way, some how bounced around a parked car and hit the house across the road!!!!.

I'll finish it there. lol

she mite have bent the steering arm best solution put her in the back and your pet dog at the front and crank up the music

Hahahaha, I did that with my ex...thus the ex...

I actually bought the line off my girlfriend...so she drives it whenever, I have actually damaged the thing more than she has...( I bent the front bar in a paddock, yes a paddock dont ask...)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...