Jump to content
SAU Community

Recommended Posts

After finally deciding on a fuel pump i opted for the walbro 255. When i went to get it installed (im too ***** to do it myself) they told me after they installed it they will check the current and may need to install a seperate relay from the battery.

Ive heard that you need to do this with some of the bosch pumps, but is this really necessary, im only going to be running (hopefully) 190~rwkws.

Should i just have them install it, then chuck it on the dyno and if the ratios are fine, not worry? or should i jsut trust them :)?

I just dont want to be ripped off.

Link to comment
https://www.sau.com.au/forums/topic/67592-fuel-pump-relay/
Share on other sites

the more voltage that gets to the pump the more it will pump! have seen reports on a VL turbo fuel pump which gave 30% more flow @ same rail pressure when it was given +14V instead of +11 like it usually sees in a VL. the thicker guage wire going to it generally the more voltage it should see, installing a separate relay is probably easier than rewiring the original one.

Link to comment
https://www.sau.com.au/forums/topic/67592-fuel-pump-relay/#findComment-1254196
Share on other sites

Like they say, more voltage = better...

however the last two pumps (one walbro, one bosch) I have installed I have had no troubles with the stock wiring at levels below 200rwkw.

I guess if I was pushing the power past that, it would be something to consider. You can always stick a multimeter on it on the dyno at full chat, see what is happening.

Link to comment
https://www.sau.com.au/forums/topic/67592-fuel-pump-relay/#findComment-1254229
Share on other sites

You need to be careful when selecting Walbro pumps. As you can see from the attached, the GSS341 is rated at 255 lph, that's at zero boost and at 13.5 volts. If you install one in tank with the standard Skyline wiring it will run at 12 volts, that's 215 lph. Then add some boost, say 20 psi (1.35 bar) and they are down to 180 lph.

flowtest-walbro.gif

Link to comment
https://www.sau.com.au/forums/topic/67592-fuel-pump-relay/#findComment-1254362
Share on other sites

  • 2 months later...

which is a better pump?? i need to get a new one but unsure on which one.

I want to try one of these to fix a problem i'm having with detonation......it will not detonate on the dyno but on the street it will randomly detonate. So i was gonna try one of these two pumps.....i currently have a r33 gtr pump installed.....running on the standard r32 gtst wiring. Any ideas would be appreciated.

Should i try a constant power from the battery???

1. bosch 040 intank.....supposedly doesnt need a sock????

2. Walbro 255l intank pump

thanks

Link to comment
https://www.sau.com.au/forums/topic/67592-fuel-pump-relay/#findComment-1381141
Share on other sites

that sounds like an idea i might try, what kind of relay did you use and where did you get it....i'm abit confused on what type to use, and then basically ground the relay......draw power from the battery and the ignition wire from the orginal wiring??? is that somewhere in the ballpark on what needs to be done?

Link to comment
https://www.sau.com.au/forums/topic/67592-fuel-pump-relay/#findComment-1381748
Share on other sites

  • 4 years later...

just use the factory fuel pump power wire as the switching power to the relay, and run a new power wire to the relay from the battery,

make sure it will carry the correct voltage over the lenght of the wire, the longer it is the more voltage drop due to resistance,

the size power cable will depend on how much power the pump will draw so get a nice thick one at lease 2.9mm2 core.

earth the relay to body and run power out of relay to pump. The relay packet will show the correct way to wire it up on the terminals.

30AMP relay will do for 1 pump.

Edited by boostn32
Link to comment
https://www.sau.com.au/forums/topic/67592-fuel-pump-relay/#findComment-4960788
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...