Jump to content
SAU Community

Recommended Posts

Curious if any one knows if i put on after market bigger dump pipes it will increase perforamce and less lag..

Also my car is running very rich im assuming its the o2 sensors would this be the case or could there be another factor causing this.

One more for ya when i run 1 bar or 1.2 bar of boost my car surges is this due to not enough fuel getting there.

any help is much apreacitated,.

Link to comment
https://www.sau.com.au/forums/topic/67600-32-gtr-dump-pipes/
Share on other sites

1. Curious if any one knows if i put on after market bigger dump pipes it will increase perforamce and less lag..

2. Also my car is running very rich im assuming its the o2 sensors would this be the case or could there be another factor causing this.

3. One more for ya when i run 1 bar or 1.2 bar of boost my car surges is this due to not enough fuel getting there.

any help is much apreacitated,.

1. R32GTR's have not so good dumps, so an upgrade is beneficial.

2. O2 sensors are irrelevant most of the time, they only run closed loop for idle and cruise. All R32GTR's I have seen benefit greatly from a tune, chip upgrade or ECU replacement (Power FC is the go)

3. Try new spark plugs with gaps at 0.8 mm.

Hope that is of some help:cheers:

do the 32's,33's and 34's have diffrent dump pipes to eachother?

R32 and R33 GTR's basically use the same cast iron dump pipe design and they are a bit restrictive. OTOH R34's use a thin-walled, welded stainless steel construction which have a larger bore and so flow better - definately an improvement, probably similar to some aftermarket designs.

I'm certain that both 33 and 34 dumps are the same. 32 are 60mm, 33 and 34 are 70mm....big difference in total flow.

If you want a set of 34 dumps, Powerplay in Sydney have at least 2 sets second hand

I'm certain that both 33 and 34 dumps are the same.  32 are 60mm, 33 and 34 are 70mm....big difference in total flow.

The R33 ones I had in my hand a few months ago looked identical to my R32 type. I didn't take any measurements, but were certainly the same material. Perhaps late production cars were similar to R34 (?? - shrug).

Anyway the R34 dumps I have now are definately an improvement, no doubt about that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...