Jump to content
SAU Community

Recommended Posts

  • Replies 141
  • Created
  • Last Reply

Top Posters In This Topic

finally broke the 8mins and got 7'59:900 in the lotus challenge...LOL  could probably shave another sec or 2 off but i cant be stuffed.  learnt some new tricks in the process though.

el capitan is a great track!!

Damn you got quick,

Second attempt got a 7'57.284

111rnurb578hr.th.jpg

I like Citta di aria for next track.

Just ran this track last night as part of the BMW M Cup. This track is awesome! First time around the track ever got a 7:53 in a BMW CSL modded.

Just noticed the 7.03 you got there Angry, looks like ive got a lot of improving to do! I'll have to race the R34 Nur VSpecII around there tonight.

did a 8 min 50 on first go in a Ford Mustang,

415 hp and lightened the full 10%, with sports - soft tyres on the front and sports - medium on the rear. Has nice cornering manners, brake into the corner and it really hugs the corner unlike some others I tried which just seem to throw you off the track.

did this in the arcade mode as I only hired it for a day.

check out the GTR story (english) vid on the net, has a german racer take an R34 round the track, he was the nissan gtr test driver and has done something like 10 thousand laps in his driving career on the nurg, he is pulling 170 mph in some areas passing traffic like a rocket!

check out the GTR story (english) vid on the net, has a german racer take an R34 round the track, he was the nissan gtr test driver and has done something like 10 thousand laps in his driving career on the nurg, he is pulling 170 mph in some areas passing traffic like a rocket!

There is a Tribute to the Nissan head test driver on the track a corner before the long straight.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...