Jump to content
SAU Community

Recommended Posts

if you want 6 speed look at the options from Trust, HKS and OS giken. or if you are made of money, Hollinger 6speed sequential. better option than paying a lot of money for a second hand R34 box.

Link to comment
https://www.sau.com.au/forums/topic/67887-r32-gtr-6-speed/#findComment-1259122
Share on other sites

Guest Mashrock

and the r34 box is a bit of a hastle to fit up.

the box is a few inches longer than the 32 box, so your rear shaft will have to be modified to fit.

and there are a few other things to look at aswell.

i was going to do this swap myself untill i found out how much it was going to cost.

Link to comment
https://www.sau.com.au/forums/topic/67887-r32-gtr-6-speed/#findComment-1260040
Share on other sites

Guest Mashrock

first went. and 5-6 wouldnt select.

2-3-4 were still fine.

all bearings were knackered. clearly wasnt looked after in jappas.

but other than that all was fine.

i can take the gearset over to my mate who was going to do the rebuild and get a quote if u like.

but i was getting it all done for cost.

Link to comment
https://www.sau.com.au/forums/topic/67887-r32-gtr-6-speed/#findComment-1260177
Share on other sites

and the r34 box is a bit of a hastle to fit up.

the box is a few inches longer than the 32 box, so your rear shaft will have to be modified to fit.

do the conversion with 34 GTR rear shaft and it will be fine

a workshop i know they done it to their "carbon R32"

a18b.jpg

Link to comment
https://www.sau.com.au/forums/topic/67887-r32-gtr-6-speed/#findComment-1260319
Share on other sites

Dont get me wrong, you can Definetly tell there are no syncros. You have to rev it a little to get it into 1st (otherwise you end up with a crunch)

Gear changes require a reasonalbly firm hand

You also have to rev match when down shifting, so as not to crunch.

You have to hold it in gear when reversing (otherwise it pops out)

But you just cant beat the whine of a dog box and the lightning quick gear changes.....did i mention the sound :( farken awsome!!!

I am using an OS triple at the moment

Link to comment
https://www.sau.com.au/forums/topic/67887-r32-gtr-6-speed/#findComment-1262330
Share on other sites

Guest Mashrock

i never had trouble getting 1st..

reverse was a pain in the ass tho. kept popping out even with you holding it firm. but i have abuck wild diff also which wouldnt have helped

gotta love the whine. and also the people at the lights looking at your car thinking there is something wrong.

then you show them what a rev limit dump looks like with race tyres.

Link to comment
https://www.sau.com.au/forums/topic/67887-r32-gtr-6-speed/#findComment-1262846
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...