Jump to content
SAU Community

Recommended Posts

okay here the story in short my car goes into rexy mode after a few minutes in cold start i have changed coil packs and all other obvious things!

sometimes will go away now iam really confussed today as the fact iam driving in rexy mode (missing a cylinder) then i turn the car off and start it agian and wat do u know fixes itself????

iam really confussed cause it goes away and then comes back but once it gets normal its fine

Has ne1 experienced this????

Link to comment
https://www.sau.com.au/forums/topic/68086-missing-r32-xperts-required/
Share on other sites

I'm in the same boat as you. ;)

What did you replace your coilpacks with? (Spitfires or secondhand stockers?) I'd be looking for hairline fractures.

I haven't checked my coilpacks but I've had UAS and Grey Imports report back with nothing. I have a feeling it could be some of my injectors playing up but I had them flow tested and cleaned about 5,000km's ago...

well firstly i replaced with brand new nissan coil pack haha they not cheap the impedence on them is also good!!!!!

iam starting to think faulty injector but i dunno

cause wen it is warming up ie i leave for ten minutes its will start missing and then go into rExy mode!

its an idle problem in the first ten minutes of driving but then becomes all sweet. but its intermitant!!!!

the engine is reasonably to new had the thing rebuilt about 8 months ago

well another thing you should maybe do is ,, take the oil cap off,, and if oil spurts out it could be ur piston rings,, thats what happend to my car..  :ufo:

sorry iam intrested in ur theory BUt wouldnt this be more of a constatnt problem mine is only intermittant and mainly on idle wen sitting for a while and after the car reaches 75-80 deg norm operating temp then it all comes good???

thanks

I agree with GTS500, I had the same trouble.

I replaced my coils with Splitfires

It ended up being the Ignition Module. Its a common problem and isn't an expensive one to fix.

well iam liking ur nolledge here

i think i will try ignition module altho i rang up to buy a new one and they want $800 bloody nissan parts.

u say not xpensive how then to do i dunno bout wrecker parts as with my luck it will **** up in a month or two??

help appreciated

My suggestions......do a leak down test, that will rule out mechanical issues. And get the injectors cleaned and flow checked. Have you cleaned the AFM lately? If not, give it a clean with some brake cleaner. If none of those cure, it I suggest getting a loan (or buy) one of Impakt's copy Consults, the diagnosis available will save you some money otherwise wasted on buying unnecessary parts.:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...