Jump to content
SAU Community

Recommended Posts

hey guys,

                does anyone know how to disable the boost sensor so that it dosent cut my fuel when i run too much boost.....

anyone help please

i have a rb20 powered r32gts-t 

any replies be appreciated

The factory map sensor only runs the dash guage, there is no input to the ecu.

The afm signal is what will cut the fuel (if there is a cut), though i could max mine at about 4500 rpm and never had an issue with fuel cuts.

Link to comment
https://www.sau.com.au/forums/topic/68109-boost-sensor/#findComment-1262162
Share on other sites

I've encountered a fuel cut on the stock R32 ecu due to injectors reaching 100% duty cycle. At 100% duty cycle there is still a little left in the std AFM's voltage.

The RB20DET required with its std turbo around 17psi to hit 100% duty cycle.

Some times 15-16psi @ ~5500rpm when the air is icy cold.

15psi made 164rwkw. 17psi may be say 170rwkw. or just over.

The RB30DET, the fuel cut was a alot earlier with much less boost.

Cruise on the dyno at 3000rpm start put the foot down boost spools instantly and fuel cuts when boost hits 8-9psi. The AFR's lean out really quickly to 13:1+.

The Fuel cut saves the motor. :rofl:

8-9psi at 3000rpm stock turbo with the rb30det is around 130rwkw when it cuts.

That doesn't really make a lot of sense as shouldn't the injectors make 160-170rwkw before maxing out????

In short.. Don't remove the fuel cut unless you want to build a new motor. :P

Link to comment
https://www.sau.com.au/forums/topic/68109-boost-sensor/#findComment-1263659
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, sort of blurring two different things together, aren't we? I just meant O2 feedback closed loop. I used to have a 0-1V LCD meter on my dash, wired directly to the O2 sensor signal. So you could easily see what it was doing. Normal running it would flick back and forth nicely. Slow down to an idle and it would keep flicking, as the ECU tried to servo to maintain stoich, but it would slow down as each swing happened until it would stay at one end of the scale. As I said above, the sensor heater is not enough to keep it hot enough when there is also little heat in the exhaust flow. Give it a blip and it would start swinging again, then peter out again. Meanwhile, idle speed control would run just fine, because unrelated.
    • It's not even O2 feedback, it's just simply when the ECU sees the closed TPS signal for whatever reason the idle will start steadily dropping until the engine dies. With the TPS adjusted to not trigger closed TPS it will idle at some ridiculously high RPM and something like 6 degrees of timing. In the absence of getting eyes on it personally and a lot of quality time doing diagnostics I couldn't tell you what the real problem was but it was interesting nonetheless
    • Oof. One of my mates has an R34 GT-R that he initially was a "I want to go twins for response and convenience" on his stock 2.6 with Kelford 272 cams, but his friends are pests and were always in his ear about their place being in the bin.   Eventually one of the 2860-5s decided to add it's own input and force his hand, so he conceded and went for a Pulsar 6262G ("G35 900") with T4 0.85 hotside.    Here's an overlay of the results, same cams, same stock bottom end, same boost, same fuel, just from a pretty tidy 2860-5 install to a Pulsar turbo on a 6boost maniifold on BP98.   Worth mentioning here, it may seem like a dead horse thing but the dyno plot doesn't tell the story of how much better it is to drive - transient response has completely changed the car, he used to have flat foot shifting to stop it having to wind up again on gear changes even at >7000rpm... now it builds boost faster than that even short shifting.   It's 100% transformed the car before you even consider how much better it holds on: Pulsar and Garrett aren't the same, but from our experience if you're just looking for a better drive and the ability to make the same or more power I think the divided G30 770 would probably be the smallest I'd go to.
    • Great work Duncan, any events local you will give it a test once all done? 
×
×
  • Create New...