Jump to content
SAU Community

Recommended Posts

On a turbo charged motor WITHOUT NOS you only need a fuel cut.

Cut the fuel on a turbo charged motor and you get what??? Nothing.. there is no fuel to create a bang.

NOS has its own delivery system, which is why you need an Ignition cut.

Cut the fuel, nos still goes in and bang.. leanout goodbye motor.

I dont think its that at all. Apexi say high horspower cars at high rpm are in danger of a split second lean out by hitting a fuel cut. Which is why they have the pro version. I dont think they were thinking of nos at the time of making it as the japs arnt too keen on nos.

I dont think its that at all. Apexi say high horspower cars at high rpm are in danger of a split second lean out by hitting a fuel cut. Which is why they have the pro version. I dont think they were thinking of nos at the time of making it as the japs arnt too keen on nos.

Yeah thats right R32-GTS, Sorry Cubes. Makes no differece NOS or not, NOS is not fuel its just extra oxygen source. This means its to stop the momentary lean out when fuel is cut but ignition is stil present (until theres no fuel left).

ok my bad with NOS being fuel. lol :)

Irrespective, you do not want a fuel only cut with NOS.

I still seriously doubt there would be enough fuel left over to ignite and cause any problems with our every day power figures.

If fuel cuts were a real danger ecu's would not be using them.

if you buy a regular power FC, and use a Bee-R rev limiter, you'll have all the dual rev limiter functionality, plus the Bee-R unit has a handbrake sensor too for launch control. I don't know if the Power FC pro has that. Both of them cut ignition and dump fuel into exhaust on hitting the rev limit (ie chitty chitty bang bang + flames = bye bye catalytic converter)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...