Jump to content
SAU Community

Recommended Posts

Hi :(

I know at least a couple of people have HKS GT-RS turbos on their R33 Skylines, and have seen some dyno results from people using them - but there are a couple of questions which have I've had that I haven't found answered yet:

What boost level is the actuator that comes with the turbo set to?

Do people use the factory fuel system - or upgrade the pump? Injectors?

What kind of 1/4 mile times have people with them on R33s achieved?

Any input would be appreciated :(

Cheers

Link to comment
https://www.sau.com.au/forums/topic/69158-hks-gt-rs-questions/
Share on other sites

hi mate i think they upgrade the fuel system with the turbo.It makes allot of scence.

P.S. Allot of people say that the hks actuators are set at 1bar permanent but i belive that this is not the case as how can people not have a lower seting of boost for their given application.

I think that it is the recomended pressure that they run best at most efficiently for heat created spoolup,response and peak hold psi.IMO not many others i think though.

Not sure what boost level the actuator comes set at but the minimum boost I can run is 0.9 although it still seems to sit at 15psi anyway, max boost is 1.2 with stock internals.

I have a bosch 044 fuel pump and 555cc nismo injectors.

Have not taken it to drags yet but got 270rwkw and not to much lag so should be in the 12s depending on tires?

This is what I found on google

Direct bolt-on to stock manifold. Includes 0.9kg Actuator, Gaskets and other Hardware. S13 requires custom or modified oil/coolant lines.

52T / A/R 0.64 / T25 Inlet / Internal Wastegate

Not sure what boost level the actuator comes set at but the minimum boost I can run is 0.9 although it still seems to sit at 15psi anyway, max boost is 1.2 with stock internals.

I have a bosch 044 fuel pump and 555cc nismo injectors.

Have not taken it to drags yet but got 270rwkw and not to much lag so should be in the 12s depending on tires?

Awesome - thanks a lot :P That pretty much covers what I was looking for.

So it drives fairly well like a pretty standard R33 when not giving it some??

Reedy, Wat rpm range does it spool up and create full boost by i am looking at putting one on my rb20 soon but i havent been able to find out wat rough area it will spool up by i've got the stock rb25 series 1 turbo on my car at the moment and i dont get full boost untill around 4000rpm lil bit after running 14psi lil bit before running 10psi.. so yer any info on spool of GTRS would be helpful thanks :D

On WWW.HKS-POWER.CO.JP (warning... in japanese) you can go to the turbos menu, and there is a section called "RB20-25" or something like that, which has a section on the GT-RS and GT2530Kai kits for R32 and R33 GTSt Skylines. It shows boost plots and dyno plots comparing between a stock R33 turbo and a GTRS or GT2530Kai to get an idea of comparative power/torque/spool performance.

The GT-RS at least on paper looks SLIGHTLY laggier than the R33 turbo, maybe ~300-400rpm later at most to reach the same boost level on an Rb25. The 2530Kai looks like its better right through the rev range than the R33 turbo. From what I've seen around the place, the 2530Kai looks like what I'd consider the perfect turbo for a "street tune" R32 GTSt with an RB20DET. Slightly better down low, and much better up high and with higher boost levels than the R33 unit.

I'm just looking for what realistcally I'd have to expect in terms of set up and general driving with one :D I have no doubt I'll like the full throttle performance of a GT-RS.

My mods are;

-Full 3 inch exhaust

-FMIC

-Bosch 044 fuel pump

-Spitfire ignition coils

-Power FC and boost kit

-Adjustable exhaust cam gear

-Nismo 555cc injectors

-HKS GT-RS turbo kit

-Z32 AFM

-Xtreme billet lightened flywheel

-UAS sports clutch kit

-Tein super street coilovers

-Whiteline front and rear swaybars

-JIC tension rods, front negative upper link, rear adjustable upper link

ahh k so not really all that much difference but yer i think i might go one of these GTRS's on the rb20 put a set of pon cams in to reduce a little bit of lag.. nice setup :rofl:

thats pretty much what i hope to do in the near future :)

;)

What I had hoped I'd be able to get away with is getting a decent fuel pump , a PFC, FMIC and a GT-RS kit and get it tuned on the minimum boost setting - is it fair to say that even if I wanted to run the "minimum" I'd still need the bigger injectors?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...