Jump to content
SAU Community

Recommended Posts

Hey guys,

I have a R33 and its sitting on 18" rims at the moment, and its been lowered already, however problem is already is that the strut in the front is like liturally 2cms off the wheels (and its not even that low) how can i lower it more, without this hitting the rubber??

Also, who does complete custom jobs in lowering (or who knows of some type of springs that will put the rear wheels in the arch)

Thanks guys

Dayne

Link to comment
https://www.sau.com.au/forums/topic/69804-slamming-your-ride/
Share on other sites

Hey guys,

I have a R33 and its sitting on 18" rims at the moment, and its been lowered already, however problem is already is that the strut in the front is like liturally 2cms off the wheels (and its not even that low) how can i lower it more, without this hitting the rubber??

Also, who does complete custom jobs in lowering (or who knows of some type of springs that will put the rear wheels in the arch)

Thanks guys

Dayne

You're car is already basically on the rubber, yet you want to lower it more? If anything, I'd be considering raising it to stock height to make it practical. I know it looks way better, but it's pretty much inevitable that you'll have more problems the lower you go.

hey fellas. He asked for advice on lowering it. not raising it. plus the bottom strut doesnt move. so 2cm is fine. it is no where near "basically on the rubber". and no its not a go-kart or a snow plow, its a skyline, a sports car, and some of might know that lowering a car's centre of gravity can increase handling potential. who said it was to look "full sik"?

Go the fully adjustable coilover option. That should get you the look your after. I had Apexi coilovers in my car, lowest point was 50mm off the ground, with the tires just tucking under the guards.

Do a coilover search; there are plenty of different brand options.

my rubber is about a cm or so away from the strut

but its a couple or so from the fender

Im about to try and put a set of king springs, super lows that have been cut even lower on, see how we go... i only have 17's on my car, i think i have a ways to go yet before im scraping bigtime :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...