Jump to content
SAU Community

Recommended Posts

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

hey ben

i got the pieces in the mail today

will install it either later tonight or 2morrow and post up the results

cheers

Eric

p.s great seller to buy off, quick replies and even quicker delivery =)

REVIEW

Hi, i promised ben i would write a review/feedback after i installed it so here goes.

I paid my money and got the boost piece in the mail about a day later (props to a great seller)

It was extremely easy to install. If I could do it in less than 5 minutes, anyone can

Stock boost on the r34 is around 5 psi low/ 7psi high (correct me if im wrong). As the boost piece replaces the solenoid, it becomes a constant high of around 10 psi (give or take 0.5 psi). This is better than the constant ground to the solenoid as it prevents the risk of damaging it. Full boost of around 10psi comes on under 3000 rpm (probably a bit less but i'm not very good at looking at the road, speedo and boost gauge at the same time). This then drops down by about 0.5 psi to around 9.5 psi or so.

Overall, its a great purchase for those that only want a little bit of boost increase. In my opinion, its only $20 or so and definately worth it for the gain.

Cheers

Eric

I got one of these delivered last week with a similar experience to ecl only on an R33 GTST sedan. 5 mins to install, great very clear instructions and the promised result of 10psi.

And for an added bonus I went to a dyno day today and with only a catback 3" exhaust, R34 stock intercooler and the magic 10psi and I recorded 176rwkw. I am very suprised at the result as there were a couple of stock 33s there that recorded the expected mid 140rwkw for comparison. Big thumbs up. Also there was no detonation but the car was quite rich :D . Big thanks!

I have sold about 14 of these and I have had feedback from about 10 people so far. All except 2 have held 9-10psi as they requested, however 2 people that have had automatics have been seeing around 13-14psi!! I am in the process of sending them more conservative ones.

I find this strange but if I find this to be consistent trend then I will have to have a manual one and another for automatics...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...