Jump to content
SAU Community

Recommended Posts

  • Replies 60
  • Created
  • Last Reply

Top Posters In This Topic

By the way...what's a sporty family car I can buy, It might come down to that if my wife gets her way LOL

Andrew

STAGEA!!!!! Basically a R33/34 4wd station wagon, powered by a RB25DET. :) You could even use all your "goodies" for this car.

There is one or two in the for sale car section.

Here is one:

http://www.skylinesaustralia.com/forums/sh...034#post1298034

:bahaha:  thats funny as hell man

You dont have a decent electronic boost controller stashed in there do you?

I'll have a look I'm sure i got an ebc but i just got to look for it hehehe

Andrew

STAGEA!!!!!  Basically a R33/34 4wd station wagon, powered by a RB25DET. :P  You could even use all your "goodies" for this car.

There is one or two in the for sale car section.

Here is one:

http://www.skylinesaustralia.com/forums/sh...034#post1298034

Hmm...not bad. The one for sale, is that a cheap price though? I was looking at perhaps getting a subaru forrester or a ford territory lol. Hence me selling these bits.

PS. Do the following items fetch much at all? Not too sure. They are all in pretty good nick.

AFM

front and rear hubs

cf bonnet, i know they fetch a bit new but what about second hand?

tein coilovers

Thanks for all your help people

much appreciated.

ANDREW

Hi Hus

please look at the wanted to buy thread. What was your number again, will give you a call.

Andrew

My number is 0422 304 918, Thanks.

Is the CF bonnet for series 1/2 ?

Is it damaged in any way?

What does it look like? Does it have vents etc?

Do you have any pics? Pics to [email protected] if you do

Is the CF bonnet for series 1/2 ?

Is it damaged in any way?

What does it look like? Does it have vents etc?

Do you have any pics? Pics to [email protected] if you do

CF Bonnet is for series 1

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...