Jump to content
SAU Community

Recommended Posts

YES DELAY CRUISE!!!!! Just got confirmation da Ceffy is on the water and should landed here in about 2 weeks.......so w/end 28-29th of May or maybe beginning of June.... is good for me and i will be out and about in my purple people eater :cheers:

Ando

  • Replies 124
  • Created
  • Last Reply

Top Posters In This Topic

I don't care where we go!! I will just be happy to behind the wheel of my Cefiro finally! Should be great so have a large turnout of Ceffies!!! Maybe we could head up to wisemen's ferry way??? Maybe south to towards the Gong.......not too keen thou for a large drive. Oh maybe head up the mountains to Leura or something....hhmm nice cold turbo induction air goodness :cheers: Really not fussed! Maybe we can organise a meeting point @ Homebush Carpark P6 and even the Cefiros from 'Northside' (think theres about 4 or so) can meet at say Chatswood or somewhere local and head to homebush together???!!!!!

MY 2 CENTS

Ando

Where is the cruise?

Undecided but i am keen on the idea of heading to mountains...IE lithgow....Leura etc...just my thought. Meet at Homebush P6 in morning

when are we going on the cruise?

Weekend of the 4-5 June....Think we should lock in the Sat 4th as some are busy on the Sunday

why aren't we going on the cruise now?

Because a couple of people have pleaded to hold off (like me oopps) for various reason...commitments, car mods, etc

and so on and so forth....

Sorry to anyone who was waiting for me to make a decision (your all very capable though :wassup: ) between a buisy work schedule and a crippling GT4 addiction I haven't been on the forums of late.

Now I have an F1 car on gt4 and im in a comfort zone I can put the controller down...

Who wants to go on the 4th June? Say meet at Penrith Panthers car park, then we can go pretty much anywhere we like from there, West out bells line of road to lithgow and back or south to the gong is a very easy straight forward drive...

im open to suggestions!

So whos up?

Due to a buisy work schedule and a horribly crippling GT4 addiction (at least I have an f1 car now) I ahve finally got back on to the forums...

Hey I like the idea of the 4th how about we meet at penrith or somthing like panthers carpark then we can go pretty much anywhere from there.

Up bells line of road to lithgow and back down?

South to the gong thats a straight forward easy from penrith?

Im with deviat so who else is up for the 4th???

Alright well it seems that the 4th is a goer! Sorry to hijack the organising but i am keen as mustard to take my new baby out for a cruz with other cefiros! She is on the docks and should be picked up next week sometime!!! WOOT!

Okay the PLAN

4th June 2005

Meet @ 10am at Penrith Panthers

Depart 10:30am SHARP!!

Head up Bells Line road to Lithgow

Lunch up there 'somewhere'.........

Head back say around 2-3pm, should get us back in Syd about 5-6ish!?!?!?!?!

Sounds like a plan???? I am open to other destination suggestions but a drive up the mountains sounds good to me!

For the boyz living around the north side we can say meet @ 9am somewhere local......dunno maybe Chatty area...not sure!

MY 2 c

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...