Jump to content
SAU Community

What caused this to happen - cracked exhaust manifold??


Recommended Posts

Hey Guys,

After the really hot track day at Phillip Island my car was sounding like it had a gasket leak on the exhaust side. Stripped her down this week only to find a cracked & severely warped exhaust manifold :)

There was a 2 inch split/crack in cyl 3's manifold pipe and the metal was tinted blue suggesting some major heat.

Anyone know if the heat was the major factor in this -or- is it more likely that the crack had been developing over time and the heat just made it worse??

hahaha.........I would have thought so Nark but its not the only thing that would cause it. Maybe if a lot of people had this happen it could be an inherent fault in the design or something......All I know is it was an absolute b@stard of a thing to pull off the block 'cause it had warped sooooo much (and warped the heat shield 2). As for the shiney S/S one, if I had more time before the next track day I would have hunted an aftermarket one down but unfortunately I had to have the car back together ready for winton. Anyway managed to get my hands on a ported std item so should flow pretty well anyway.

Ash....thanks for the suggestion but my car has an a'market ecu etc etc and only got dyno'd recently so I know shes not running lean. Do have the req'd free flowing exhaust which helps but I'm thinking maybe when my manifold was match ported they could've shaved too much off in that area which led it to crack.

Did it snap and studs?

Looking at the designm they will always want to warp as the heat form all 6 cylinders is focussed int he centre.

But one thing i have noticed at a few Voc track days, you boys hok straight into full throttl work once leaving pit lane. I always do a lap of light throttle / med revs stuff to get a bit of heat into not old tyres, brakes, gearbox, diff etc, but also because i have a stainless steel manifold and i dont want to hit it with a bucket load of heat straight away.

So maybe a slighlty slower out lap may help reduce the heat shock/distortion?!?!?!

Troy.......Man it was a b@stard. Luckily it only snapped one bolt so not much drilling out to be done. B@stard part of it was that it was warped so that the studs were forced up against the edges of the holes in the manifold preventing it from being taken off the block. The diff was really apparent when I went to put the new one on....fitted straight up with the studs right in the centre of the holes.

You are right about the warping happening at the centre of the manifold as the crack was in the pipe off cyl 3 and once the manifold was off the block it had warped in a concave shape.

I usually do a slow lap outta the pits mainly putting heat into brakes etc - never thought about things like the exhaust manifold. Going against that is the fact that I'm running street rubber (more heat=less grip) so I tend to hit the gas straight after the out lap.

Will go easier for the first couple of laps at Winton and see how I go....

Where is the crack?

right neat the plate?And troy, en EX man will get most the heat-up done just idling before you hit the track man.

Yeah it'll rise somewhat more... but most if its already done.

Its the mechanical bits after the motor that need the warmup more-so

Ash.....Nah mate the crack was no where near the flange plates that connect to the block or the flange plate that connects to the turbo. The crack was close to where the pipe off cyl 3 mates into the common runner that lead to the turbo - but the crack actually ran along cyl3's exhuast pipe.

check the crappy attached pic......

I personally think it was some type of failure in the flux capacitor or possibly the Mr. Fusion......:D

Nah but really, could be simply a defect in manufacturing? What about timing and cams? Have you had diff cams put in? I'm not expert but you know how they play with timing (or is is exhaust cams) and it draws more heat away from the engine, perpahs it's caused the manifold to get super hot. Could be combination of both! If there was an impurity in the metal could be a probelm...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...