Jump to content
SAU Community

Recommended Posts

For those who don't know, Nissport is a workshop in Braeside/Mordialloc.

Anyhow, my clutch died so I called a few places...

I got the usual bunch of ppl who gould not be fuxored explaining, or recomending a type of clutch for my car/driving habbits, and those who just wanted to sell me some crap they most likely made the biggest margin from.

Spencer at Nissport was more than happy to spend 15 mins on the phone asking me lots of questions about my driving habbits, cars modifications and power output so that he could then give ne a few recomendations as to which clutches would be most suited for me.

anyhow in the end i went for a full faced carbon composite organic clutch with an 850kg pressure plate. The clutch is much lighter than the stock clutch that was in there before and has heaps more bite than the standard clutch, even when it was new.

I was worried a little at first, but he assured me that the light pedal feel is attributed to the installation. He also found my spigot bush was a bit rooted and replaced that at no extra charge. He also explained how that wasn't installed properly last time either.

I asked him to take care with my car b/c it has recently had a full respray and he did.

He also gave me a follow up call the next day to see if I was happy, and to once again re-assure me that the light pedal feel should not reflect the bite of the clutch.

Overall I rate his customer service 10/10.

As for the clutch it is still in the "running in" period, so I will give a better review in a week or too.

So any1 else out there like I was, that doesn't know what to get, how much it should cost, etc, give spencer a call at Nissport and he will happily try to determine what you need, and more importantly, explain WHY....

Link to comment
https://www.sau.com.au/forums/topic/70335-my-experience-with-nissport/
Share on other sites

Hey Inark,

$800 installed.

I could have gotten it done cheaper elsewhere, but I did that 3 years ago, and I didn't want to do it again.

Last time spigot bush was not installed properly and made a rattle/whistle noise when clutch was engaged CONSTANTLY for 3 years.

The adjustment was so bad, the clutch was hard (and it was a stocker), and the friction point was only millimeters from the floor....

This time I just wanted it done right, and I would have gladly paid a little extra.

But, the thing it, labour was $200 this time. The last time I got it done, labour was $250....

Clutch was $550, and $50 for machine and surface grind of flywheel. Some places only machine flywheel, not surface grind.

yeah I guess most things...

He was telling me a bout a brake upgrade with brembo slotted rotors, and ***** pads (I wasn't paying too much attention b/c I thought I saw a scratch on my car)...

They had a 300ZX with the engine ou so they could upgrade the turbo's

I asked about dyno tuning and I was told they hire dyno time on the wolf research dyno...

I dunno how good they are with other stuff, I'm just saying he was honest, customer service was very good, and they were very reasonable priced. These are qualities I like, search for and think should be rewarded, hence this post.

I guess if you want something else done you should suss them out yourself, sorry I cant help...

they specialises in 300zx's

and i think from memory that they used to import skylines under the old regulations so know their way around a skyline

my mate with an NA 300zx goes there and is generally happy with their service

spencer sounds like good bloke, but loves the sound of his own voice, and is great at making you buy more than you actually need...

joe (the mechanic) is a great guy too and knows his shit...

cheers,

Warren.

Hey Warren, you hit the nail right on the head mate.

Spencer did try to sell me brakes that I dont need, but that doesn't upset me, b/c that's just business! He was very helpful, and did take the time to eplain a fair few things for me...

When I told him I was going to replace my swaybars, he asked what bushes I was going to use and if I had any rubber grease. I told him i was on my way to bursons to get some, and he gave me a small sachet and then spent another few minutes telling me how I should do it.

Now that may not sound like much of a big deal, but he didn't have to do it, and I appreciate the time he spent helping me. It's the small aspects of customer service that are missing from many workshops I've been to that makes me go elsewhere sometimes.

(BTW, I dont think you are bagging him, and I am not defending him, just sharing my thoughts)

cheers

How far off the flois friction point?

Next time you talk to him ask him the question can ya?

I have always wondered when I sat in new cars with that have a bit of balls out of the factory and had a play with the clutch and gearstick and they are always feather light compared to my clutch.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...