Jump to content
SAU Community

Garrett GT28RS "Disco Potato" Direct Bolt On?

S2peed

By S2peed,
in Engines & Forced Induction

 Share

Recommended Posts

discopotato03 Grand Master

discopotato03

Posted
Posted

The GT28RS CHRA is very similar to the HKS GT2530 , the compressor wheel is a 60mm 62 trim instead of a 60mm 63 trim . The tip height is slightly greater making it a more efficient wheel with slightly better flow . In original form the GT28RS uses a .86ARR T2/25/28 flange exhaust housing and a .60ARR TO4B compressor cover . ATP Turbo are now doing them with the optional GT28 compressor cover (internally same as TO4B) which has the two bolt inlet and three bolt outlet compressor cover . There is a .64 exhaust housing you can use but dont know if its suitable for TT RB26 .

S2peed Rookie

S2peed

Posted
  • Author
Posted

Well I am trying to hit the 450- 500 WHP with bolt on Turbos, downpipe and exhaust system, Intake system, intercooler kit, Camshafts, and a stand alone engine management.

I am looking for turbos with very minimal lag but able to push hard through the RPMs with out letting up in the high rpms.

I like the HKS turbos but there just too much money and for that money i can get the other components I mention up top. So I am looking at the garrett turbos. GT28R looks pretty good the GT28RS looks like is going to lag too much for my liking so I dont know.

Also I want to know if this Garrett Turbos will just Bolt right in to the Factory things. Thanks for your help

600hp Proficient

600hp

Posted
Posted

I would still go a set of HKS turbo's i don'r know why the americans don't like spending money on proven good parts.

we have GT-SS turbo's, we are currently producing around 480hp at the wheels.with hardly any lag.we make around 220AWKW at about 4000rpm, with a riv limit of 8500rpm.

Go the HKS path.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • sonicii
      Anyone running the VQ37VHR with forced induction?

      By sonicii · Posted

      I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Dose Pipe Sutututu
      Mistakes were made, my R34 Story

      By Dose Pipe Sutututu · Posted

      Fuark, at least the motor survived. What brand was the fitting that snapped?
    • GTSBoy
      Anyone running the VQ37VHR with forced induction?

      By GTSBoy · Posted

      Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • GTSBoy
      Starter motor replacment teeth count.

      By GTSBoy · Posted

      Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...