Jump to content
SAU Community

Recommended Posts

hey, Wondering what else you have for sale from the 34 and how much power can you get out off that turbo?. Cing you'v sold the injecters n rail's. What was your TR of power in the skyline when you had the turbo, Injecters & rails & the inlet manafold. Before putting the RB26?

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

hey, Wondering what else you have for sale from the 34 and how much power can you get out off that turbo?. Cing you'v sold the injecters n rail's. What was your TR of power in the skyline when you had the turbo, Injecters & rails & the inlet manafold. Before putting the RB26?

never fitted this setup to my car due to ECU issues....previous owner claimed approx 280 rwkw and was running Microtech and Poncams then he went for an RB26 install...hey, i have nothing else for sale....

Cheers,

Michael

never fitted this setup to my car due to ECU issues....previous owner claimed approx 280 rwkw and was running Microtech and Poncams then he went for an RB26 install...hey, i have nothing else for sale....

Cheers,

Michael

Thanx for the info. I just bought a same turbo n wanned to no how far the turbo would go. By the way, Your price is lil to much. I got myn for a 600. But the guy needed the money. goodluck with the sale

Thanx for the info. I just bought a same turbo n wanned to no how far the turbo would go. By the way, Your price is lil to much. I got myn for a 600. But the guy needed the money. goodluck with the sale

hey...thanx musti for that unwanted and un-solicited info : P seems you know how to impress on these forums with the magical $600...No, Goodluck to you and your $600 turbo....

Cheers,

Michael

Thanx for the info. I just bought a same turbo n wanned to no how far the turbo would go. By the way, Your price is lil to much. I got myn for a 600. But the guy needed the money. goodluck with the sale

ROFL!!!! $600 ahahahaha, yeap right sure AHAHAHA. Thats cheaper than what you can buy it from japan, you dreaming dude hope the turbo doesnt **** up on you

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...