Jump to content
SAU Community

Recommended Posts

was looking into some balancers and this was mention to me

WE NOW HAVE A BONDED BILLET STEEL BALANCER THAT IS A WILD CARD. FOR THE RACER WHO NEEDS A BALANCER FOR HIS TRANSPLANT AND WHO CAN LIVE WITHOUT POWER STEER AND A/C. THE BALANCER COMES WITH A SAFETY SHIELD THAT BOLTS ON THE FRONT. THIS SHIELD IS MANDATORY FOR CARS THAT ARE DOING THE ¼ MILE IN 12 SECS OR LESS. IT PREVENTS THE OUTER FROM LEAVING THE ENGINE IN CASE OF A RUBBER FAILURE.

there are lots of cars that have ran 12s and i dont think its an issue....what if you runs 11s and 10s does the scrutineering get tougher?

Link to comment
https://www.sau.com.au/forums/topic/71168-harmonic-balancers-question/
Share on other sites

s15s are wicked...but they make it into the 11s not 12.0@245rwkw cough cough 330rwkw + nos  :headspin:

Hey I wasn't talking to you, I was talking to gtrsux.

I think what you are trying to say, is that cast harmonic balancers (schtandard) are not approved by ANDRA, and that an SFI approved balancer(billet/forged/aftermarket) is preferred. But check out the Compak Attak thread, if they let a car slip onto the podium 200lbs underweight what makes you think they will nit-pick balancers? Unless you are going to try and blackmail them?

Guest two.06l
Hey I wasn't talking to you, I was talking to gtrsux.

I think what you are trying to say, is that cast harmonic balancers (schtandard) are not approved by ANDRA, and that an SFI approved balancer(billet/forged/aftermarket) is preferred. But check out the Compak Attak thread, if they let a car slip onto the podium 200lbs underweight what makes you think they will nit-pick balancers? Unless you are going to try and blackmail them?

solve all the problems.....run an N1 balancer.....billet steel

good enough to get our race car ANDRA tech'd

Theo runs one as well..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...