Jump to content
SAU Community

Recommended Posts

was looking into some balancers and this was mention to me

WE NOW HAVE A BONDED BILLET STEEL BALANCER THAT IS A WILD CARD. FOR THE RACER WHO NEEDS A BALANCER FOR HIS TRANSPLANT AND WHO CAN LIVE WITHOUT POWER STEER AND A/C. THE BALANCER COMES WITH A SAFETY SHIELD THAT BOLTS ON THE FRONT. THIS SHIELD IS MANDATORY FOR CARS THAT ARE DOING THE ¼ MILE IN 12 SECS OR LESS. IT PREVENTS THE OUTER FROM LEAVING THE ENGINE IN CASE OF A RUBBER FAILURE.

there are lots of cars that have ran 12s and i dont think its an issue....what if you runs 11s and 10s does the scrutineering get tougher?

Link to comment
https://www.sau.com.au/forums/topic/71168-harmonic-balancers-question/
Share on other sites

s15s are wicked...but they make it into the 11s not 12.0@245rwkw cough cough 330rwkw + nos  :headspin:

Hey I wasn't talking to you, I was talking to gtrsux.

I think what you are trying to say, is that cast harmonic balancers (schtandard) are not approved by ANDRA, and that an SFI approved balancer(billet/forged/aftermarket) is preferred. But check out the Compak Attak thread, if they let a car slip onto the podium 200lbs underweight what makes you think they will nit-pick balancers? Unless you are going to try and blackmail them?

Guest two.06l
Hey I wasn't talking to you, I was talking to gtrsux.

I think what you are trying to say, is that cast harmonic balancers (schtandard) are not approved by ANDRA, and that an SFI approved balancer(billet/forged/aftermarket) is preferred. But check out the Compak Attak thread, if they let a car slip onto the podium 200lbs underweight what makes you think they will nit-pick balancers? Unless you are going to try and blackmail them?

solve all the problems.....run an N1 balancer.....billet steel

good enough to get our race car ANDRA tech'd

Theo runs one as well..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...