Jump to content
SAU Community

Recommended Posts

Hey guys, When i press the break on my car my driving lights, tail lights and dash lights come on..

If it helps, when the key is in the ignition, and i hit the breaks it makes a beep sound as if the lights are on (because they are) even without the car started.

If you had this problem, or know someone who has, please let me know how you fixed it.

Thanks in advance..

Dayne :wassup:

Link to comment
https://www.sau.com.au/forums/topic/71285-electrical-problems/
Share on other sites

Sounds like you have a really bad earth. Somewhere in your electricals when you put the brakes on the power is finding another path back through to other car parts. This would mean that your brake lights will also be dimmer than usual.

To fix it? Try looking at your fuses first? Then look at where your loom, lights, etc... are earthed to the car. This is the most common cause, where the lights aren't earth correctly and therefore earth via other bits.

Found the problem,

dissconected my light i replaced, and it was fixed... looks like there is a difference between the harrneses, might of been out of a series 1 or something.. or series 2 insted of the 1.5

Changed it. and its fixed!!

thanks 4 the tips guys, made me realise + fix the problem

Dayne

Uh guys, wen its un plugged the problem is fixed, and when all the lights are in bar one the problems fixed, yet when the harness is full of lights the problem is there again?? any ideas on whats next...?

Thanks again. Ps. When i break the lights do come on brighter, so its not as if its not safe or anything its just damn annoying!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...