Jump to content
SAU Community

Recommended Posts

  • Replies 64
  • Created
  • Last Reply

Top Posters In This Topic

We've been discussing this in another thread so I'll recap some of the discussion.

There are so many octane boosters to choose from that the choice is difficult to make. The best octance booster are Nulon Pro Strength Octance Booster, NF Octane Booster Racing Formula and Toluene.

The first two you can buy from the shop the later from hardware stores and servo stations. These octane boosters will raise PULP by about +2.5RON. The octane rating is related to when the engine will begin detonating and pinging, it is not a reflection on additional power. With a higher octance rating though you can advance the timing and therefore get more power.

There are a number of boosters that provide little in the way of improved RON (+0.2RON) but will add more horsepower, these contain nitromethane. Some examples of this are PowerFuel Super Street Nitro Based, PowerFuel MaxRace Nitro Based.

Hope that helps.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/7137-octane-booster/#findComment-105006
Share on other sites

Higher RON will protect your engine from detonation, a big plus. The amount of power from these boosters is relatively minimal, so I would go for the protection, allows you to run higher boost safely. If you want the best of both worlds then use VP Motorsport fuel, 107 octane plus shitloads more power.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/7137-octane-booster/#findComment-105096
Share on other sites

MRE,

All octane boosters will cause deposits on your spark plugs, they will tend to go an orangey color. I said it had the highest octane rating, which I was presuming was for the drags, I wouldn't recommend using octane booster all the time.

I would use it but only on the occasions when you know you're going to be running high boost and leaning on the car alot.

See'ya

:burnout:

Link to comment
https://www.sau.com.au/forums/topic/7137-octane-booster/#findComment-105143
Share on other sites

Ait,

I wouldn't bother using it in normal street driving, just wasting you money, I bet if you take your plugs out they'll look like shit. Seriously if your using BP Ultimate (98RON) then I wouldn't bother, just add it if you go racing or drag racing. The higher boost will need the additional octane to ensure no detonation.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/7137-octane-booster/#findComment-105150
Share on other sites

I'd definately agree with not using commercial octane booster....the crap fouls up your plugs. It has been suggested although, you keep a bottle in the boot for those times you can't get 98ron fuel (of course only the good quality stuff..if you got it in Coles or Woolies, then I reckon it would be crap...like their oils).

Toluene on the other hand can be bought from petroleum companies, I think in 20 litre drums, and mixed with your petrol (ask advice on the proportion per tank)....but care must be taken as it is a CARCINOGEN.....(causes cancer....very dangerous stuff). The best advice, I think though if you're not drag racing is just use one of the commercially available 98ron fuels (BP Ultimate, Shell Optimax or Mobil Synergy 8000 (only available in NSW/SA & Vic I think))....if you read their Material Data sheets, they are pretty well on par with each other...although I prefer the BP (don't know why...just seems to go better).

Link to comment
https://www.sau.com.au/forums/topic/7137-octane-booster/#findComment-105339
Share on other sites

This from an old thread (Backyard Race Fuel) initiated by rev210 on 27/8

Toluene = Methyl-Benzene.  

A search of the net uncovered that it is not on the NIOSH carcinogen list, but it adversely affects the central nervous system.

Link to comment
https://www.sau.com.au/forums/topic/7137-octane-booster/#findComment-105364
Share on other sites

Originally posted by Ozzy

.but care must be taken as it is a CARCINOGEN.....(causes cancer....very dangerous stuff

It's definately not a carcinogen. It is dangerous tho. Don't go sniffing it on purpose. You will die on a high.

BTW ordinary fuel IS carcinogenic, linked to leukemia.:D

Link to comment
https://www.sau.com.au/forums/topic/7137-octane-booster/#findComment-105410
Share on other sites

Originally posted by GTS-t VSPEC

Either way, I would advise that you use gloves when mixing it. No point getting sick from it, then you can't drive your car!

See'ya:burnout:

It's pretty good at cleaning oily grime your hands if you forget to wear gloves:D The central neverous system effects occur if sniff it. Thats why harware stores have it locked up sometimes (to prevent those who do this from stealing it)

Mind you ordinary petrol is far worse to spill on your hands but most people change fuel filters and stuff without gloves. Maybe they should wear some.

Link to comment
https://www.sau.com.au/forums/topic/7137-octane-booster/#findComment-105413
Share on other sites

I promise to make this my last on the subject, but the US ATSDR (agency for toxic substances and diseases registry) website states........

'How likely is toluene to cause cancer?

Studies in humans and animals generally indicate that toluene does not cause cancer.

The EPA has determined that the carcinogenicity of toluene can not be classified. '

The above statement doesn't sound too convincing to me....I definately wouldn't clean my hands with it !!!

:eek:

Link to comment
https://www.sau.com.au/forums/topic/7137-octane-booster/#findComment-105440
Share on other sites

ARhhh...now I've got a bottle of STP to get rid off. I think I'll keep it for those times when I won't have Premium around.

Thanks guys, think I'll stop using these things. For drag racing days, I'll use only Nulon Pro. Supposed to be one of the best besides toulene.

If 98 ron is good enough, how much power loss is there since our cars are supposed to run on 100 ron?

Link to comment
https://www.sau.com.au/forums/topic/7137-octane-booster/#findComment-105570
Share on other sites

Originally posted by Ozzy

I promise to make this my last on the subject, but the US ATSDR (agency for toxic substances and diseases registry) website states........

'How likely is toluene to cause cancer?  

Studies in humans and animals generally indicate that toluene does not cause cancer.  

The EPA has determined that the carcinogenicity of toluene can not be classified. '

The above statement doesn't sound too convincing to me....I definately wouldn't clean my hands with it !!!

:eek:

The mineral safety data sheet (australian version) does not classify toluene as a carcinogen, nor does any other world standard for toxicity. As I said before however, ALL general use petrol contains carcinogenic substances. And the vapours from petrol contain these very same carcinogenic substances. Like to fill your car up in a chemical protection suit now? If you don't then you aren't reacting consistantly with the belief that toluene might be carcinogenic.

I find that the same people that label toluene a carcinogen are blissfully unaware that petrol is recognised world wide as a carcinogen. They probably even wash parts (and hands) in it and siphon petrol using their mouth?:D

Link to comment
https://www.sau.com.au/forums/topic/7137-octane-booster/#findComment-105585
Share on other sites

Toluene.....you'r supposed to put it in your tank....not clean your teeth with it!!

You can get it at Autobarn 20L drum $48 it's a heap better than any of the retail octane boosters being pure Methyl Benzine. Now the hot weather is here I add 5L to my tank when I go to the drags or racetrack as a hedge against detonation.I think this gives an octane rating of 99.8. incidently none of the BP servos I enquired at could supply it .

Link to comment
https://www.sau.com.au/forums/topic/7137-octane-booster/#findComment-105869
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
×
×
  • Create New...