Jump to content
SAU Community

Recommended Posts

hey guys, got a standard rb20 auto cefiro, under full load it just coughs and farts, and sounds like its fluttering, but its going nowhere!

any ideas?

sound like a dead air flow meter to you guys? cos i have tried 2 with no improvement!

the problem is worse when its warming up, where it does it even on 1/4 throttle

Link to comment
https://www.sau.com.au/forums/topic/71576-cefiro-running-real-bad/
Share on other sites

  • 2 weeks later...

Has it got enough power to fire the ignition properly?

Long shot but alternator might be dead - get the electricals checked.

Also check ECU isn't in limp mode for some reason it could be mega rich n retard for some reason or another but if the ECU is limpin it then atleast you have a better idea where.

Could be anything, leak in the cooler pipes? .. good luck tho.

Could be inlet leak as above person mentioned.

My inlet manifold gasket blew on firewall side underneath and couldnt be seen. Same symptoms as you and was also worse when not at full temp. I guess because as the metal heated up and expanded it closed the leak down a bit.

  • 4 weeks later...

the cause of this problem is easy to pinpoint. For starters you drive an ex taxi piece of shit, that probably has clocked the speedo around a couple of times on the poor old 'de' so really you will be chasing your tail forever with the rb snotbag trying to find the problem. Go down to your local servo, fill up a 20litre jerrycan and set fire to the **** !!

  • 3 weeks later...

it doesnt have a boost leak?? my 33 wouldnt rev past 5000 on any boost, took me ages to find it, i alot of parts like you have, only to find i had a split intercooler hose, real prick to see. boost would show correctly on the guage, it didnt show i was losing any, thats why i didnt think it was a leak... usually its just a simple little problem.

cheers

Linton

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Fuark, at least the motor survived. What brand was the fitting that snapped?
    • Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...