Jump to content
SAU Community

Pbr H/d Clutch Kit To Suite Rb20det

boosted_32
 Share

Recommended Posts

boosted_32 Proficient

boosted_32

Posted
  • Author
Posted
how much power will it hold???  

What bits does it come with???

Shop said it would be good for 200rwkw comes as a complete kit with the clutch plate, cover assembly and release bearing. Sold my car before I got to put it in.

boosted_32 Proficient

boosted_32

Posted
  • Author
Posted

Ok just for everyone’s interest I am not accepting anything lower then $300 + postage on top of that the only reason I’m selling this as I’ve sold my car and didn’t have a chance to put it in. It’s brand new!!! Ok these clutch kits are sold at Revolution Motosports on the gold coast (where I brought this from) I am very good friends with the manager there and therefore he sold this to me at wholesale rates $300 I’m not making any money on this nor am I going to be loosing any money as he sells them retail for $495 so my loss your gain.

yogi000 Mentor

yogi000

Posted
Posted
Dude just give him $300... lol Its an awsome price!

If i has the cash just atm id snap it up

so u dont have the cash, so zip it champ :P

i'm not trying to rip anyone off, i can buy this at trade price too. Good Luck

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...