Jump to content
SAU Community

Recommended Posts

alright well i was bein a bit of an idiot tonight in the wet and i was doin a burnout and my car just died started it up again and it kept wantin to die so i just clutched it a bit till i could park it somewhere then i popped the bonnet and the dump pipe was glowing and the water in the over flow was boiling so i left it for an hr then it would start then die so i left it another hr then it would start hve a real rough idle then die as soon as it was underload does ne 1 know what i hve done ur help will be much appreciated

Link to comment
https://www.sau.com.au/forums/topic/72747-rb20-problems/
Share on other sites

I think he just cooked it and possibly blew off an IC hose.

Thats if he is lucky.

Worse case is its leaned out causing the coolant to boil and exh. valves burnt, possibly even blowing a hole in a piston. :cheers:

Which is why it a good idea to often throw the car on a dyno every 6 months or a year for a power run to check the AFR's are in check.

Link to comment
https://www.sau.com.au/forums/topic/72747-rb20-problems/#findComment-1338399
Share on other sites

I think he just cooked it and possibly blew off an IC hose.

 

Thats if he is lucky.

 

Worse case is its leaned out causing the coolant to boil and exh. valves burnt, possibly even blowing a hole in a piston. :cheers:

 

Which is why it a good idea to often throw the car on a dyno every 6 months or a year for a power run to check the AFR's are in check.

Head Gasket, Holed Piston, Burnt Valves.... I would go for the latter... Pull your plugs out and you will find they do not all look the same...

Good Luck

TT

Link to comment
https://www.sau.com.au/forums/topic/72747-rb20-problems/#findComment-1338466
Share on other sites

sounds like uve done a head gasket, just the fact that water pouring out of ur overflow is one major factor.

Pull out all ur plugs check for water in ur cylindars and take off ur oil cap and see if its milky....if it is, ure up for a new head bro.

just exactly how long was ur burnout? lol

Link to comment
https://www.sau.com.au/forums/topic/72747-rb20-problems/#findComment-1338923
Share on other sites

Water coming out of the overflow doesnt nesseserally mean a head gasket. My car used to do it when it was in traffic, but it had a hole in it as well... I also lost my radiator cap and cooked the engine... They will take a fair bit. It was that hot that it wouldnt run and was knocking during idle.... Picked it up in the afternoon and it was fine, but for sure i was lucky with that one.

Link to comment
https://www.sau.com.au/forums/topic/72747-rb20-problems/#findComment-1340293
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Started sifting thru my brakes to decide which ones I will run on Clem   Made me think I should just put them all on Silver...for when brake fade just isn't an option   Should be able to bump rotor up from 343x32 to 348x36 off Supra. Not sure if the Supra annulus is right for the Alcons or APs but trying g to find a used Supra\M4 rotor to test fit The Alcons seem to gain 1-2mm clearance which all helps  
    • So car is getting a few mods to the cage and some jacking points welded in Meantime Ol Silver gets a new gearbox and shiny clutch.  Old Box is being set aside for Clem  
    • Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
×
×
  • Create New...