Jump to content
SAU Community

Recommended Posts

I got the following parts forsale

AP Engineering power fc to suit rb20det, has brand new hc, 4 weeks old $1500

HKS 2535 turbo, t3 flange, comes with all oil + water lines, hks elbow $1500

hks hypermax coilovers, height and damper adjustable, as new cond, suit r32 gtr/gts4 $1500

Tomei 256 cams to suit rb20det, 8.5mm lift, done 500km with trust adjustable cam gears $1000

Works meister alloy wheels, 17 x 8 and 17 x 9, as new condition, gold center, silver dish, as new condition, brand new 235/45/17s on rear 50% 225/45/17s on front $2750

Greddy profec b spec 2 boost controller - $400

cusco 1 way lsd mechanical diff center to suit gtr/gts4 never installed $700

parts are all in excellent condition, awaiting removal this week

im not open to offers, all prices are reasonable so dont annoy me with offers

pictures available for interested parties

How suitable would turbo be for drift on the rb20? When would full boost be available at what psi? What kinda kw will the turbo support?

Thanks.

i get fullboost around 4500 rpm and the car makes 300 rwhp at 16 psi

cheers

also 6 x r32 gtr injectors with ballast resistor

just cleaned and serviced 3 weeks ago

$300

Hey buddy i'll take these injectors off you... does that mean they've been flow tested? How much for postage to me at postcode 2536 in NSW?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...