Jump to content
SAU Community

Recommended Posts

  • Replies 182
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

Bump.

I just bought a can of that Dupli-colour metalcast paint in the red. Will 1 can be enough? they only had one can left.

I was thinking of using Septone Automotive's Brake Caliper & Drum Paint for the primer as I already have a few cans of the stuff lying around my garage. Anybody know if this would be okay to use with the dupli-colour?

Also, anybody tried just taping up the surrounding area than applying the paint? Or would it be better off in the long run to pry the Calipers off & paint them.

Cheers

Oh & schmiddy, excellent job. If it wasn't for this thread I wouldn't even have considered doing this for myself :)

hahaha no wories mate glad to be an insperation ahahah, man i would ge the proper primer, just incase, for the sake of it, cos it would be a shame to have them on a week and the paint not take proply or something, and yeah i took the whole caliper of, not to hard a job just brake line and 2 bolts, turns out awsome that way, one warning, bleed your barakes once there back on as takin the lines of gets them full of air, and watch reaplying the caliper that brake fluid doesnt get on the newly painted caliped, that shit chews the paint straight off, good luck mate

Awesome Thanks for that Shmiddy I should be getting around to it soon. I'm going to take a few test sprays on some old brake pads I've got lying around to get an idea of the finish with the primer I'm going to use.

Cheers again buddy :(

  • 2 weeks later...

For those guys still looking for Duplicolor Metalcast, the Australian distributor is Hoits/Hoyts (damn forgotten the spelling already) and they are on 1800 021 106.

AutoOne stock Duplicolor (the normal range) but can definitely order Metalcast for you. If the storeman gives you a funny look, get them to ring Nationals or ring Hoits themselves on the 1800 number.

Cheers!

I just taped/masked mine up around the disks and they came up fine. The slight overspray on the discs disappears after about 5 minutes of driving! Taking the discs and brake lines off is a pita.

i havent seen this product(or read the complete thread) but am tipping its just a candy ..would i be right in saying its put over the top of a silver?It will also be an acrylic system which will just wash off with any type of solvent.... Another way of doing it is strip the paint off the calipers then spray etch primer on them then paint them in a silver ground coat and get a product called SEM candy concentrate in what ever colour candy you want....add the concentrate in some 2K clear and thats it....Its certainly a better way of doing it and will last as long as your paint on your car and will have to use paint stripper to get it off....To answer shans question,this system has been used for 20 odd years and we have painted complete cars/motorcycles with it...I am sure that people are aware that this is not anodising...its just an anodise look....cast cannot be anodized properly

Hi Troy

From their website, it is an enamel that you prep the surface with their pressure pack "Adhesion Promoter" for bare metal then paint with just the one type of paint.

And yep, I'm pretty sure everyone understands that it is paint and not anodizing. Still looks a treat for old calipers.

Mark

Hi mark...acrylic/single pack enamels both have the same characteristic's altho enamel will go over anything and not play up where as acrylic over single pack enamel fry's up...so having said that once you paint anything in single pack enamel your stuck with it untill you bare metal it.....both still wash off with solvent tho,which would concern me with using this product as some wheel cleaners may strip it off....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • New CAS just turned up from NZ Wiring. Looks like a nice bit of gear.  So, yeah. Triggered, bro. Realised I may as well do the cam belt while mucking about with it so will order one of them.
    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
×
×
  • Create New...