Jump to content
SAU Community

Question regarding Vaccum hose that leads to Wastegate from IC piping

gts-wpn

By gts-wpn,
in Engines & Forced Induction

 Share

Recommended Posts

gts-wpn Enthusiast

gts-wpn

Posted
Posted

I have a question regarding the Vaccum hose that connects from the intercooler piping and then hooks up with the bleed valve then goes to the wastegate actucator. May sound like a stupid question but is it better drill a hole and to run the vaccum hose before the intercooler(between the turbo and the intercooler) or after the intercooler(between the intercooler and the plenum)?

Does it have much effect on the way the bleed valve will work considering there is a slight pressure drop after the compressed air goes through the intercooler and then into the engine?

otto Collaborator

otto

Posted
Posted

I would have thaught after the i/c would be better, you want the w/g to see the pressure the engine gets(remembering your boost gauge is also after the i/c so you can see the pressure your engine gets). i think the pressure before the i/c is irrelevant But i could be wrong.

GTR-Ben Proficient

GTR-Ben

Posted
Posted

Why does it matter what pressure the wastegate is seeing compared to the engine? Thats why you have the gauge tapped closest to the engine so you can adjust with that.

Why do aftermarket Electronic boost controllers have a seperate sensor for the guage..?

The wastegate needs good response.. so taking it as close to the turbo as possible would make sense to me? Why alse would factory wastegates get there pressure from right off the turbo compressor housing?

I may be wrong here.. it is probably not too major where you take the pressure from. Seems to work well either way.. ?

Stock GTS-T takes it from the turbo compressor. Stock GTR takes it from after the throttles..

Sydneykid Grand Master

Sydneykid

Posted
Posted
R32 gtst's have the nipple on the turbo compressor housing instead of the intercooler pipe like the R33's.

I agree with the above in that it should be taken as close to the turbo as possible.

Ditto, keep the hoses short, air compresses and you get more dampening the longer the hose is. That means slower response.:P

blind_elk Grand Master

blind_elk

Posted
Posted

The thing is, you don't want the wastegate opening prematurely. If you activate the wastegate off the back of the compressor, then the wastegate opens when the compressor "spikes". Also, you get more wastegate creep having the "signal" close to the wastegate.

If you run the wastegate off the back of the compressor, then the engine "sees" wastegate setting minus pressure drop. If you run the wastegate off the plenum, then the engine "sees" wastegate setting. I know which one I'd rather be running.

otto Collaborator

otto

Posted
Posted
Why does it matter what pressure the wastegate is seeing compared to the engine? Thats why you have the gauge tapped closest to the engine so you can adjust with that.

Why do aftermarket Electronic boost controllers have a seperate sensor for the guage..?  

The wastegate needs good response.. so taking it as close to the turbo as possible would make sense to me? Why alse would factory wastegates get there pressure from right off the turbo compressor housing?

I may be wrong here.. it is probably not too major where you take the pressure from. Seems to work well either way.. ?

Stock GTS-T takes it from the turbo compressor. Stock GTR takes it from after the throttles..

I thaught the r33 gtst from factory took it from the plenum after the i/c and the r32 gtst from the compressor. now your probably right about which way is better but if the factory is the grounds for your argument tell me why did the factor have it at the comp for r32 then change to the plenum for its next more advanced model the r33!

Sydneykid Grand Master

Sydneykid

Posted
Posted
I thaught the r33 gtst from factory took it from the plenum after the i/c and the r32 gtst from the compressor. now your probably right about which way is better but if the factory is the grounds for your argument tell me why did the factor have it at the comp for r32 then change to the plenum for its next more advanced model the r33!

The R33 has a solenoid the R32 doesn't:cheers:

GTR-Ben Proficient

GTR-Ben

Posted
Posted
The thing is, you don't want the wastegate opening prematurely. If you activate the wastegate off the back of the compressor, then the wastegate opens when the compressor "spikes". Also, you get more wastegate creep having the "signal" close to the wastegate.

If you run the wastegate off the back of the compressor, then the engine "sees" wastegate setting minus pressure drop. If you run the wastegate off the plenum, then the engine "sees" wastegate setting. I know which one I'd rather be running.

For a bleed valve this is probably the case, for a good EBC.. this should not be a problem.

With an EBC the settings are changed from what the engine sees as this is where the gauge part is plumbed, so it really matters not what the wastegate sees as long as it gets a fast responsive signal.

I would rather a spike cause underboosting than overboosting also. With the signal taken futher down the track, with a long pipe to the gate.. the spike will cause a boost spike (bad) But with a good EBC none of that should happen.

otto.. I think the main difference is to do with the boost control systems on the GTR and R33 etc as it is a basic bleed valve in a way.

Just throwing ideas around here as I recently had the same ideas from both sides of this discussion.. :)

I then looked at the apexi installation for external wastegate, and decided to go with this.. it made sense to me and they probably know best for their product..

I have never had any spikes or problems running either way though to be honest..

Sydneykid Grand Master

Sydneykid

Posted
Posted
The thing is, you don't want the wastegate opening prematurely. If you activate the wastegate off the back of the compressor, then the wastegate opens when the compressor "spikes". Also, you get more wastegate creep having the "signal" close to the wastegate.

If you run the wastegate off the back of the compressor, then the engine "sees" wastegate setting minus pressure drop. If you run the wastegate off the plenum, then the engine "sees" wastegate setting. I know which one I'd rather be running.

What difference does it make? I set the IEBC to open the wastegate at the boost I want,. I don't care which piece of air I use to open the wastegate, it's all air. I juts want short hoses so the response is fast, not dampened by a couple of metres of hose.:)

PS; faster response = less time for boost spikes

GTR-Ben Proficient

GTR-Ben

Posted
Posted
What difference does it make? I set the IEBC to open the wastegate at the boost I want,.  I don't care which piece of air I use to open the wastegate, it's all air.  I juts want short hoses so the response is fast, not dampened by a couple of metres of hose.:)

PS; faster response = less time for boost spikes

:)

otto Collaborator

otto

Posted
Posted
The R33 has a solenoid the R32 doesn't:cheers:

They could still have hooked it up to the comp if they wanted to regardless but they decided not to. an ebc has a soilinoid does this mean the ebc would be better hooked to the plenum?? is it better to run a bit more hose and have the solinoid in a cooler place or run it short and have it be fried by the turbo. anyhow most of the time its closer to hook it to the plenum when you start to install ebc/ bleeder or whatever.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Does that German restaurant still exist in the old place out the NW end of Goulburn? When I say "out the NW end of"...I am really being vague. It was 1997 when I was last there, and the only point of reference I can recall is that it was on the opposite side of the main drag from the big merino. And when I say "opposite side of the main drag", I don't mean "on the main drag". It was either a couple of streets back from there, or might have even been out in the sticks a bit further. Was an old farm building or mill or somesuch. And when I say "the big merino" I might actually be thinking of a completely different part of town, because I just looked on maps and the big bugger is not where I remembered him to be! The food was good, consisting largely of various German mystery-meat sausage/loaf things and kartofflen.
    • GTSBoy
      R33 GTR running -9 with no tune

      By GTSBoy · Posted

      So while the second sentence is completely correct and the whole point of the conversation, the first sentence bears consideration. If this bloke is just hoping to throw big turbos on and drive it around, because there are no helpful facilities at all in his tropical paradise** then he likely has zero chance of even knowing what the TP is on the last column in the stock maps, let alone know whether the ECU is operating anywhere near it or past it. So the point is very very moot. And, per what I said before, at stock boost on those turbos, you may well be off the end of the map. **I'm just back from Vanuatu, so I know exactly what small Pacific nations can be like wrt paradise without requisite facilities. But it's not even that simple. I put a high flow on my car and had to drive it around without a proper tune because of the lack of opportunity*** to put the bigger AFM and injectors into it to allow it to be tuned. I had to turn the boost down to less than I had before, and back off the boost controller's ramp, because it was exploring parts of the map that it didn't drive in before, and really couldn't access for tuning on the dyno either, and so was pinging. It was still well within the last column, because when I first**** set up the Nistune on the Neo I rescaled all axes of the maps to give some more space to explore. ***Family dyno was broken ****This was 13 years ago, and the TIM thing wasn't a thing then and so TP would definitely grow when pushing past the stock tune's limits.
×
×
  • Create New...