Jump to content
SAU Community

Recommended Posts

the air will be cooled LOWER THAN AMBEINT TEMP

Umm maybe u should go back to school, ambient temperature is the temperature of the air hitting the cooler, the cooler no matter how fast u drive your car through the "wind" will never be below ambient temperature, nor will ever equal ambient temperature, its not possible.

AS A SIMPLE ANSWER DONT POST SHIT AS FACTS WHEN U HAVE NO CLUE WHAT YOUR TALKING ABOUT.

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Umm maybe u should go back to school, ambient temperature is the temperature of the air hitting the cooler, the cooler no matter how fast u drive your car through the "wind" will never be below ambient temperature, nor will ever equal ambient temperature, its not possible.

AS A SIMPLE ANSWER DONT POST SHIT AS FACTS WHEN U HAVE NO CLUE WHAT YOUR TALKING ABOUT.

:werd:

  • 3 weeks later...

i just read this thread for the first time, and my eyes are watering...

this thread is tops!

ROFLMAO

it's got to be a practical joke to sucker people in, surely!

hey, what if he put a nitrous spray on the intercooler? :lol

restrictions in your na setup is about as good as ceramic blades in your muggler tip. Every little bit of extra pipe and stuff will kiil performance. You can buy it if you want and wrap it in a towle and leave it under your bed.

Just don't put it on. It will slow you down and anyone who looks under your bonnet will think you are a pure ricer.

now for the constructive bit.... If you want to increase your performance. Get a pod and partition it off from the rest of the engine bay and run some of the springy pipe stuff from the bottom left hole in your front bumper. This way you will be getting air that doesn't pass through the radiator and AC condensor. You could also heat wrap the pipe that is in the rest of the engine bay to keep the temps down a bit more.

I hope this is useful info

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Got you mate. Check your email!
    • I see you've never had to push start your own car... You could save some weight right now...
    • Sounds good.  I don't 100% understand what your getting at here. When you say, "I keep seeing YouTube videos where people have new paint and primer land on the old clearcoat that isn't even dulled down" do you mean this - there is a panel with factory paint, without any prep work, they paint the entire panel with primer, then colour then clear?  If that's what you mean, sure it will "stick" for a year, 2 years, maybe 3 years? Who knows. But at some stage it will flake off and when it does it's going to come off in huge chunks and look horrific.  Of course read your technical data sheet for your paint, but generally speaking, you can apply primer to a scuffed/prepped clear coat. Generally speaking, I wouldn't do this. I would scuff/prep the clear and then lay colour then clear. Adding the primer to these steps just adds cost and time. It will stick to the clear coat provided it has been appropriately scuffed/prepped first.  When you say, "but the new paint is landing on the old clearcoat" I am imagining someone not masking up the car and just letting overspray go wherever it wants. Surely this isn't what you mean?  So I'll assume the following scenario - there is a small scratch. The person manages to somehow fill the scratch and now has a perfectly flat surface. They then spray colour and clear over this small masked off section of the car. Is this what you mean? If this is the case, yes the new paint will eventually flake off in X number of years time.  The easy solution is to scuff/prep all of the paint that hasn't been masked off in the repair area then lay the paint.  So you want to prep the surface, lay primer, then lay filler, then lay primer, then colour, then clear?  Life seems so much simpler if you prep, fill, primer, colour then clear.  There are very few reasons to go to bare metal. Chasing rust is a good example of why you'd go to bare metal.  A simple dent, there is no way in hell I'm going to bare metal for that repair. I've got enough on my plate without creating extra work for myself lol. 
    • Hi, Got the membership renewal email but haven't acted yet.  I need to change my address first. So if somebody can email me so I can change it that would be good.    
×
×
  • Create New...