Jump to content
SAU Community

prob with my car ( any 1 can help )

WAR33
 Share

Recommended Posts

WAR33 Apprentice

WAR33

Posted
Posted

hey i have got a R33 and wenever i go to slow down or go up my drive way , go to park it , or put it in reverse sometimes the revs will drop and it will some times stall or go really low and then kick its self back up ... i have cleaned out the idol speed motor and it still does it could it be a vacum leek or piping to the turbo not conectted prop if any 1 has any ideas and can help thanks heaps

Link to comment
https://www.sau.com.au/forums/topic/74579-prob-with-my-car-any-1-can-help/
Share on other sites
benm Grand Master

benm

Posted
Posted
Yup have a good read of that thread, I had the same problem. In the end what solved it for me was cutting the wire that goes from the fuel pump back to the ecu (tells it when to stop pumping). Never once had an issue after that :thumbsup:
SRG33 Enthusiast

SRG33

Posted
Posted

I had this exact problem! It turned out it that when the car was getting serviced, my mechanic noticed that there was a vacuum leak near the idle speed motor.. He fixed this and reset the timing, and i havent had any problems with idling/stalling since.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Roy
      Ben's R32 Gtst Build

      By Roy · Posted

      Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • GTSBoy
      Another little story of weird shit happening

      By GTSBoy · Posted

      Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • MBS206
      Another little story of weird shit happening

      By MBS206 · Posted

      Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Shizu
      Returning after a long time!

      By Shizu · Posted

      Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
    • dbm7
      Looking for a part number for this part here

      By dbm7 · Posted

      Did some FASTing ...got the impression that the actual part# was a moot point ; seems all of these hardlines for coolant are discontinued/NLA... like, I take it you're after the hardline that bolts onto to the manifold...that's NLA according to amayama & nengun .... ...just to clear up some confusion, they typically mounted the AAC valve to the intake manifold somewhere near a coolant passage, so the body of the valve heats up & holds it open when engine's up to temp - no coolant flows through the valve, it's a mechanical, thermal connection.
×
×
  • Create New...