Jump to content
SAU Community

Recommended Posts

These aren't the biggest turbo in terms of HP. I think they are rated at 320ps.

The advantage is they are ball bearing which means the RB25 will spool this very early.

With supporting mods you could probably pump out around 220rwkw. Though if you're going to the trouble of replacing the turbo you'll be asking yourself why you didn't pay the extra $500 and get something a little bigger.

Expect to pay upwards of $1200 ~ for a good condition example. Check to make sure if it comes with oil / water lines as this will set you back $100 or so plus intake modifications.

You don't need two threads to ask the same question.

If it's a turbo question then it's pretty obviously going to go in the Forced Induction section.

Also there is a shitload of info on here about this turbo and how it goes on an RB25. It's an old turbo.

A 2535 would be better suited to an RB25 but don't underestimate what a street weapon a 2530 RB25 will be. The first question that should be asked when upgrading turbo is what do you want to do with the car?

A 2540 is not often recommended.

Check out http://www.skylinesaustralia.com/forums/sh...ead.php?t=55845

and do some more reading.

Oh, and have fun. ;)

Like everyone has stated, ask yourself what you're after in your car. If you're after big horsepower, don't go this turbo. I have a 2535 on mine and in my opinion, it's heaven on a stick. An RB25 with a 25XX turbo is going to give you a very quick response, with good power but don't expect to see the rwkw mark exceed much more than 250rwkw with a 25 series turbo. A 2530 would be lucky to even get there with 220rwkw about it's theoretical max. I currently make 220rwkw on just 12psi with my 2535, which is rated just a bit higher than the 2530.

For $1200, you can't go wrong if all you are chasing is around 200-220rwkw and a very responsive street car. As others have said, don't underestimate this turbo as it will certainly give your car a kick in the arse that will have you smiling every time ;) Best of luck mate.

With supporting mods the 450hp GCG rebuild wud go close, maybe 250-260rwkw is more likely though. Mind you its still damn responsive which is awsome, when you go past 250rwkw you tend to get abit more lag and that isnt the best on a street car.

Gotta say 16psi at 3,000rpm is pretty damn cool!! And if ur makin near on 300rwhp, well most would be pretty happy with that too.

if your chasing say 270rwkws what turbo is suitable. Ive read all the related threads posted by other members but got lost in the information. For examples sake, would a GCG turbo be capable?

seach button, and half the stickie threads in this section will answer that question for yous

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This. A 3d wheel alignment is like $120...just take it to the shop. Since theres probably multiple adjustments that need to be made after changing something. Mine has front/rear lower arms, traction rods, tension rods, camber arms, toe arms, front upper arms, hicas kit, sway bars and coilovers. I measure from the edge of the bolt holes on the originals and set the same length on all the adjustable stuff to dial it as close as I could to OEM. Took it straight for alignment; it didnt feel right at all...after alignment, it feels perfect. Similarly i've just changed the springs on another car; and I still needed multiple adjustments to bring it back in spec.
    • A full Veilside kitted JZA80 Supra in Meriken park in Kobe city a few weeks back
    • Its a well known brand in New Zealand; its a rebrand of the Rhino RAV3.  I don't know what the wiring difference *is* between the rev.1 (installed about 15 years ago) and rev.2; but as you say I would think its reasonable that it uses the same immobiliser relay circuits. I had a look but couldnt see a similar harness; but didnt move things around since I didnt want to mess with it   It was one of AVS well known Authorised Installers; I spoke to AVS themselves about it but theyre unsure hence seeking advice more so from the skyline community who are more familiar with the actual car and its wiring. Im in Auckland; but the installer is on the other side of the city so hes very reluctant to come back to even look at it to confirm something isnt connected into the wrong wire.  I dont want to drop the name since they *did* do a really good job for the most part. Everything is very tidy and he fully replaced all the alarm wiring, all the sensors, the wiring to the door motors, installed a switch which was never installed in the first place...really happy with the alarm install itself..just not this one issue. We all make mistakes, if it is the alarm, I just want my fuel pump getting proper switched, fused, power as it was; without having to shell out for an auto electrician to switch a wire and tell me it was the alarm. 
    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
×
×
  • Create New...