Jump to content
SAU Community

Recommended Posts

I have been practicing my emergency braking lately after getting new pads and machined rotors and have noticed. my oil warning light will flash on for a second. Has anyone else seen this under heavy braking. I guess it is probably normal and nothing to worry about. I hope.

And yes my oil levels are correct.

Link to comment
https://www.sau.com.au/forums/topic/75339-oil-warning-light-when-heavy-braking/
Share on other sites

Thats not good, you are getting oil surge.

What type of oil are you running and how hot is the car when you are doing this because i wouldn't expect to have problems as the oil pick up is up the front of the sump and the oil would be sloshing to the front under braking.

Do you have a bent sump by any chance?

I am running redline 10w 40 and its happening when engine is at operating temp. Its a pressure light. My sump aint bent either. Has anyone else seen or heard of this happening.

Only happening under very heavy braking and just before i come to a stand still. And only for a second.

the light that always comes up on my 32 is the funny thing with heat waves coming of it... is that engine temp or something>>?? or the oil one... cus sometimes i'll just be driving and it comes on but it flashes irregularly... then i will restart the car and it'll be alright.. just depends... Can any1 help with this?>

I wouldn't worry unless you are unemployed.....a new cat can set you back 3-400.

As for the oil pressure light coming on...I would assume that while the engine is running you would only have 2-3 litres of oil in the sump at any one time, therefore, a VERY hard brake would send this oil flying towards the front. Even though the pickup is at the front, you can still fit 2-3 litres in front of it. I would say that BHDave is correct in saying you are experiencing oil surge. It only takes a split second for it to suck a small amount of air and the pressure drops to zero for a split second after that, hence the light coming on, until regular oil pressure returns.

I seriously think you don't have anything to worry about but if you are, take it to a mech who has an oil pressure guage and get your car tested.

Oil surge is pretty simple.....all the oil in a wet sump engine like an rb comes thru the oil pick up in the sump. It is in one place usually at the deepest part.

But as the car moves around (esp under high g forces) the oil can move around so much that there is no oil for it to pick up. Result...no oil to the pump and therefore not going around your engine. eeeek.

There are a heap of techniques to deal with this in Rbs such as bigger sumps, baffles and trapdoors in the sump, restrictors in the oil line to the head, foam in the cam covers, larger oil return galleries.

Under brakes is one of the biggest g forces most cars have, and if there is low oil level yhou might get this problem. I know you said your oil levels are correct which is why I didn't mention this first.

Also could be a problem with the oil pressure sensor? Perhaps get a workshop to add an extra oil guage as a first step if you are sure oil levels are OK.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
    • Could be correct. Meter might be that far out. Compare against a known 5 ohm 1% resistor.
    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap.  (edit: I went out and did it right now, the line I had chosen did appear to have no vacuum on it, it used to go to the front of the intake, I've now completely blocked that one off at the bracket that holds several vacuum lines by the firewall.  I T'd into the vacuum line that goes from that bracket to the vacuum pump at the front of the car, but no change in the MAP readings).  Using the new vacuum line that has obvious vacuum on the hose, im still only getting readings between -6.0 and -5.2.  I'm wondering why the ECU was detecting -5.3 when nothing was connected to the MAP nipple and ECU MAP selected as the source. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
×
×
  • Create New...