Jump to content
SAU Community

Recommended Posts

I have been practicing my emergency braking lately after getting new pads and machined rotors and have noticed. my oil warning light will flash on for a second. Has anyone else seen this under heavy braking. I guess it is probably normal and nothing to worry about. I hope.

And yes my oil levels are correct.

Link to comment
https://www.sau.com.au/forums/topic/75339-oil-warning-light-when-heavy-braking/
Share on other sites

Thats not good, you are getting oil surge.

What type of oil are you running and how hot is the car when you are doing this because i wouldn't expect to have problems as the oil pick up is up the front of the sump and the oil would be sloshing to the front under braking.

Do you have a bent sump by any chance?

I am running redline 10w 40 and its happening when engine is at operating temp. Its a pressure light. My sump aint bent either. Has anyone else seen or heard of this happening.

Only happening under very heavy braking and just before i come to a stand still. And only for a second.

the light that always comes up on my 32 is the funny thing with heat waves coming of it... is that engine temp or something>>?? or the oil one... cus sometimes i'll just be driving and it comes on but it flashes irregularly... then i will restart the car and it'll be alright.. just depends... Can any1 help with this?>

I wouldn't worry unless you are unemployed.....a new cat can set you back 3-400.

As for the oil pressure light coming on...I would assume that while the engine is running you would only have 2-3 litres of oil in the sump at any one time, therefore, a VERY hard brake would send this oil flying towards the front. Even though the pickup is at the front, you can still fit 2-3 litres in front of it. I would say that BHDave is correct in saying you are experiencing oil surge. It only takes a split second for it to suck a small amount of air and the pressure drops to zero for a split second after that, hence the light coming on, until regular oil pressure returns.

I seriously think you don't have anything to worry about but if you are, take it to a mech who has an oil pressure guage and get your car tested.

Oil surge is pretty simple.....all the oil in a wet sump engine like an rb comes thru the oil pick up in the sump. It is in one place usually at the deepest part.

But as the car moves around (esp under high g forces) the oil can move around so much that there is no oil for it to pick up. Result...no oil to the pump and therefore not going around your engine. eeeek.

There are a heap of techniques to deal with this in Rbs such as bigger sumps, baffles and trapdoors in the sump, restrictors in the oil line to the head, foam in the cam covers, larger oil return galleries.

Under brakes is one of the biggest g forces most cars have, and if there is low oil level yhou might get this problem. I know you said your oil levels are correct which is why I didn't mention this first.

Also could be a problem with the oil pressure sensor? Perhaps get a workshop to add an extra oil guage as a first step if you are sure oil levels are OK.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...