Jump to content
SAU Community

Recommended Posts

Hi all,

I've got to move my RB26DETT which came in my car. I got approx 6000-7000km out of it since buying the car. By all indications the motor should have 120-130K on it (a serious estimate) based on car, odo, and condition of the motor.

The motor had the standard oil pump fail on the drag strip just before the line, coasting through to a 12.5 @ 111mph on .7 / .8 bar. The motor was shut off immediately, but sustained some bearing damange (Scored not spun). The motor is currently sitting on the engine stand with the crank out (needs to be linished, but should be otherwise fine, would recommend microtest). The motor made 253rwkw @ 1 bar on the dyno, and compression tested at 160psi in all but cylinder number 5, which was 155psi.

Basically on offer is the lot, complete head with coils, complete block with crank, rods, pistons, sump, inlet manifold with plenum etc, exhaust manifolds, standard turbos, dumps etc.

The engine is missing alternator/powersteering/AC/starter motor/injectors/loom.

As I have to post a price in this section, I'll say $3K ono and take it from there.

YES, I will seperate parts - however please email me [email protected] so this dosent turn into an unmanagable post. Please feel free to ask me any questions.

Also available:

- JUN Crank collar (BRAND NEW) - $200

- Aftermarket Front pipes to suit twins (not sure on brand) - $200

- Standard RB26 AFMs $150 ono

- APEXi power intake pod filters (practically brand new w/ brackets) - $250 ono

- Standard ECU $200

Will update this post accordingly.

Cheers

Rick

Link to comment
https://www.sau.com.au/forums/topic/75399-eoi-rb26dett/
Share on other sites

  • 2 years later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...