Jump to content
SAU Community

Recommended Posts

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

obviously theres not going to be a pits that will let everyone off with illegal stuff.

any dual pillar mount is illegal. your bov is illegal if it vents to atmo. your pod needs to be secured properly. your neons must follow the guidelines (ie. mustnt be able to see the tubes at all). your exhaust cant be too loud. you should be able to get permits for everything except the pillar mount and exhaust. they dont do permits for exhausts anymore apparently.

depends on the car, you and the inspector with what you can get away with.

When I got a yellow for being too low, I was told I needed permits for BOV (atmo), strut brace, pod filter, non standard seat rails. Already had permit for dual pillar gauge and exhaust. I went to Welshpool, and that was quite easy...aside from the 4 hour wait in line. They inspector crossed everything off, took it around the block and gave me all of the permits.

My brother in law is a cop, I asked him about permits and stickers and what he looks for. He told me that if he sees any more than 5 aftermarket mods he will ask to see permits. If no permits he will send the car off to get them, ie sticker.

He also told me that this is what he did, not a written policy - they can give you a sticker for any mod that doesnt have a permit.

If you are worried about getting a sticker off, it would be worth while IMO to go and see guys like C-Red, they have modded cars with permits and deal with the guys at the pits often enough to know what is ok and what isnt. Might save a bit of hassel.

Yeh I got done on Sunday night in the City at a booze bus, my friend behind me in his 180 also got done. On the way to go to Vic Park. Cant believe I got done for not having a permit on BOV and sticker on the windscreen. Had permits for everythin else. Twas such bu***hit! Thought to myself can they do this?

The cops we got were such b**tards. Said things like

- "this is what you get when you drive a car like this"

- "use your brains when buying a car"

- "You think youre car's hot, its not!"

- "Tell your friends that were coming to get them and that there is no escape"

And we didnt even back talk to get this kinda treatment. Also threatened to be arrested and further fined. I felt it was a real attack on jap cars. Anthing jap was getting sent to the side and checked for a "work order".

Really has left me pi**ed off all week.

Oh and "series 2" what were you doing when you got pulled over? were you speeding or just cruisin along.

Let us know how Welshpool is coz ive been told good things - I myslef have been to Warick and East Perth. Warick sux, East Perth not so bad it depends on who you get as an inspector.

And Im also worried that my suspension my be too stiff - will they check it again? anyone?

Cheers.

i got the sticker off yesterday at stock road got over with everything and got permits for everything .

Twista i was just going along booze bus and they pulled me to the side they reckon my BOV was to load but it was the bus behind me with their airbag or air brakes.

load of crap

Guys you gotta expect to be looked at when you're pulled over because the cars we drive standout from the norm and the cops know that we carry out mods.

If you don't bother getting permits who's to blame. I agree that they shouldn't give you any extra attitude because you drive an import, but remember they are human and will react to any attitude you show them.

When dealing with traffic cops be polite, your're on a hiding to nothing if you give them shit.

My understanding is that any mod has to be within the ADR guidelines (ride heights, noise etc) and technically should have a permit unless the mod is a standard fit to a model of car in the same range.

IE If you own a car that as an option had a larger wheel package available when new, you can fit wheels of that size without getting a permit. Always pays to check with licencing.

Insurance is another issue. HBF told me that my car will be covered as long as all mods are permitted by licencing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
    • When I said "wiring diagram", I meant the car's wiring diagram. You need to understand how and when 12V appears on certain wires/terminals, when 0V is allowed to appear on certain wires/terminals (which is the difference between supply side switching, and earth side switching), for the way that the car is supposed to work without the immobiliser. Then you start looking for those voltages in the appropriate places at the appropriate times (ie, relay terminals, ECU terminals, fuel pump terminals, at different ignition switch positions, and at times such as "immediately after switching to ON" and "say, 5-10s after switching to ON". You will find that you are not getting what you need when and where you need it, and because you understand what you need and when, from working through the wiring diagram, you can then likely work out why you're not getting it. And that will lead you to the mess that has been made of the associated wires around the immobiliser. But seriously, there is no way that we will be able to find or lead you to the fault from here. You will have to do it at the car, because it will be something f**ked up, and there are a near infinite number of ways for it to be f**ked up. The wiring diagram will give you wire colours and pin numbers and so you can do continuity testing and voltage/time probing and start to work out what is right and what is wrong. I can only close my eyes and imagine a rat's nest of wiring under the dash. You can actually see and touch it.
    • So I found this: https://www.efihardware.com/temperature-sensor-voltage-calculator I didn't know what the pullup resistor is. So I thought if I used my table of known values I could estimate it by putting a value into the pullup resistor, and this should line up with the voltages I had measured. Eventually I got this table out of it by using 210ohms as the pullup resistor. 180C 0.232V - Predicted 175C 0.254V - Predicted 170C 0.278V - Predicted 165C 0.305V - Predicted 160C 0.336V - Predicted 155C 0.369V - Predicted 150C 0.407V - Predicted 145C 0.448V - Predicted 140C 0.494V - Predicted 135C 0.545V - Predicted 130C 0.603V - Predicted 125C 0.668V - Predicted 120C 0.740V - Predicted 115C 0.817V - Predicted 110C 0.914V - Predicted 105C 1.023V - Predicted 100C 1.15V 90C 1.42V - Predicted 85C 1.59V 80C 1.74V 75C 1.94V 70C 2.10V 65C 2.33V 60C 2.56V 58C 2.68V 57C 2.70V 56C 2.74V 55C 2.78V 54C 2.80V 50C 2.98V 49C 3.06V 47C 3.18V 45C 3.23V 43C 3.36V 40C 3.51V 37C 3.67V 35C 3.75V 30C 4.00V As before, the formula in HPTuners is here: https://www.hptuners.com/documentation/files/VCM-Scanner/Content/vcm_scanner/defining_a_transform.htm?Highlight=defining a transform Specifically: In my case I used 50C and 150C, given the sensor is supposedly for that. Input 1 = 2.98V Output 1 = 50C Input 2 = 0.407V Output 2 = 150C (0.407-2.98) / (150-50) -2.573/100 = -0.02573 2.98/-0.02573 + 47.045 = 50 So the corresponding formula should be: (Input / -0.02573) + 47.045 = Output.   If someone can confirm my math it'd be great. Supposedly you can pick any two pairs of the data to make this formula.
×
×
  • Create New...