Jump to content
SAU Community

Recommended Posts

The best tyres for street and strip are R rated tyres. These are street legal, but have few water channels and provide alot of tyre block in contact with the road. The compound of R rated tyres is much softer than normal tyres, giving it better traction but wear much quicker. An R rated tyre will last about 5-10,000km's of normal driving.

The Potenza R's are very good, and popular for both track and strip. Nitto's are very good, but difficult to get and very expensive.

I'd recommend the Potenza's, but just keep them for the drags, don't waste them on daily driving, unless money is not an issue.

See'ya:burnout:

Those tyres should provide a reasonable level of traction at your power level, but it depends more on how you launch the car. If you can slip the clutch and get the power down gradually then they should be fine, if like me you have twin plate and dump the clutch then they will not provide enough grip.

I'm getting some Potenza R's from a race car, they only have 15% tread left, not enough for racing, but plenty for drags. You will need to experiment with tyres, I run 265's at the drags and they don't provide enough traction, hence my move to the R rated tyres.

I'd experiment with some second hand tyres while at the drag strip, but normal road tyres are not as good as the R's. If you can pick some up off a race team then you can get them very cheap.

See'ya:burnout:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...